HP Cooktop 10GBE manual Configuration Script Files Usb//d1/test.cfg

Page 17

Port 13 is ENABLED

Port 14 is ENABLED

Port 15 is ENABLED

Port 16 is ENABLED

Port 1 Installed CU SFP

Port 1 Approved CU SFP

NOTE: If the module console displays C characters instead of . characters, return to step 14 to restart the Xmodem transfer.

17.Press Ctrl + Shift + _. The following message appears:

Command: D)isconnect, C)hange settings, send B)reak, E)xit command mode X)modem send >

18.Enter d.

19.To update the firmware on any other pass-thru modules installed in this enclosure, begin at step 4.

Updating the firmware image using a USB key and the Onboard Administrator CLI

NOTE: The firmware update uses the Onboard Administrator Xmodem support with a firmware file hosted on an HTTP, FTP, or TFTP server. The firmware transfer can take up to seven minutes to complete.

If no HTTP, FTP, or TFTP server is available, you can download the pass-thru module firmware file to a USB key which can then be inserted into the active Onboard Administrator USB port.

To update the image:

1.Copy the pass-thru module firmware file to the FAT32 formatted USB key in the \ directory.

2.Create a text file named text.cfg containing the following line: hello

3.Copy the text.cfg file to the USB key in the \ directory.

4.Insert the USB key into the active Onboard Administrator USB port.

5.Log in to the active Onboard Administrator CLI.

6.At the Onboard Administrator prompt, enter show usbkey. The following message appears:

Configuration Script Files

---------------------------------------

usb://d1/test.cfg

7.At the Onboard Administrator prompt, enter show oa network. The following message appears:

Onboard Administrator #1 Network Information: Name: marketing3

DHCP: Disabled

IP Address: 16.83.88.66

Netmask: 255.255.252.0

Gateway Address: 16.83.88.1

Primary DNS: 16.110.135.51

Updating the 10GbE pass-thru firmware 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Part Number December 2010 Second Edition 10GbE Pass-Thru Module User GuideIntended audience Contents Electrostatic discharge Pass-thru module architecture FeaturesIntroduction Redundant paths to server bays XModemPort mapping Dual pass-thru modules Component identification Resets10GbE Pass-Thru Module front panel DescriptionDescription Manually configuring the pass-thru module Installing the pass-thru moduleInstalling the module Module securityAccessing the pass-thru module CLI remotely Accessing the pass-thru module CLIProduction mode CLI Accessing the pass-thru module CLI locallyCommand Result CLI menuInstalling SFP+ transceivers Replacing an existing module Replacing a pass-thru moduleMethods for updating the 10GbE Pass-Thru Module firmware Updating the 10GbE pass-thru firmwareEnter R. The following message appears Enter C. The following message appearsEnter N. The following message appears Enter y. The following message appearsEnter x. The following message appears Configuration Script Files Usb//d1/test.cfg Performing a serial firmware image download Updating the firmware image using the serial portBaud rate 9600 Data bits Parity None Stop bits Flow control Additional references For more informationCause Action TroubleshootingHealth LED on the pass-thru module is not on Try another mini-USB to DB-9 RS232 cable Download fails after starting to download the firmware file Pass-thru module configuration is corruptSFP+ transceiver port is disabled General specifications Technical specificationsCategory Specification Port namesMini-USB to DB-9 serial adapter pin assignment Physical and environmental specificationsFrom Wire Shell Braid Technical specifications Regulatory compliance notices Regulatory compliance notices Regulatory compliance notices Grounding methods to prevent electrostatic discharge Electrostatic dischargePreventing electrostatic discharge Acronyms and abbreviations Network access server Media Access ControlPower-On Self Test Local-area networkIndex Index
Top Page Image Contents