HP Cooktop 10GBE manual Physical and environmental specifications, From Wire

Page 25

Port	Link	Ena	Speed	Neg	Approved

12	Up/Downlink	Dis/Ena	1Gb/10Gb	On/Off	Yes/No

13	Up/Downlink	Dis/Ena	1Gb/10Gb	On/Off	Yes/No

14	Up/Downlink	Dis/Ena	1Gb/10Gb	On/Off	Yes/No

15	Up/Downlink	Dis/Ena	1Gb/10Gb	On/Off	Yes/No

16	Up/Downlink	Dis/Ena	1Gb/10Gb	On/Off	Yes/No

Physical and environmental specifications

Category	Specification

DC inputs	12 VDC: 6.25 A maximum per pass-thru module

Power consumption	75 W maximum per pass-thru module

Operating	10° to 35° C (50° to 95° F)
temperature

Storage temperature	-40° to 70° C (-40° to 158° F)

Operating humidity	5% to 95% RH noncondensing

Storage humidity	5% to 95% RH noncondensing

Pass-thru module	267.7 x 192.79 x 27.94 mm (10.5 x 7.5 x 1.1 in.)
dimensions

Weight	1.7 Kg (3.7 lbs.)

Safety	• TUV to UL 60950-1, and CAN/CSA C22.2 No.
		60950-1 and to EN 60950-1
	•	CE Marking
	•	RoHS 6/6 compliant

Mini-USB to DB-9 serial adapter pin assignment

From		Wire	To

Connector	Contact		Connector	Contact

DSUB9F	2	Black	Mini-USB	3

	3	White		2

	5	Green		5

	1	DB-9 pins 1, 4, and 6 are connected.

	4

	6

	7	DB-9 pins 7 and 8 are connected.

	8

				Technical specifications 25

Image 25

Contents Part Number December 2010 Second Edition 10GbE Pass-Thru Module User GuideIntended audience Contents Electrostatic discharge Introduction FeaturesPass-thru module architecture Port mapping Dual pass-thru modules XModemRedundant paths to server bays Component identification Resets10GbE Pass-Thru Module front panel DescriptionDescription Manually configuring the pass-thru module Installing the pass-thru moduleInstalling the module Module securityAccessing the pass-thru module CLI remotely Accessing the pass-thru module CLIProduction mode CLI Accessing the pass-thru module CLI locallyCommand Result CLI menuInstalling SFP+ transceivers Replacing an existing module Replacing a pass-thru moduleMethods for updating the 10GbE Pass-Thru Module firmware Updating the 10GbE pass-thru firmwareEnter R. The following message appears Enter C. The following message appearsEnter N. The following message appears Enter y. The following message appearsEnter x. The following message appears Configuration Script Files Usb//d1/test.cfg Performing a serial firmware image download Updating the firmware image using the serial portBaud rate 9600 Data bits Parity None Stop bits Flow control Additional references For more informationHealth LED on the pass-thru module is not on TroubleshootingCause Action Try another mini-USB to DB-9 RS232 cable SFP+ transceiver port is disabled Pass-thru module configuration is corruptDownload fails after starting to download the firmware file General specifications Technical specificationsCategory Specification Port namesFrom Wire Physical and environmental specificationsMini-USB to DB-9 serial adapter pin assignment Shell Braid Technical specifications Regulatory compliance notices Regulatory compliance notices Regulatory compliance notices Preventing electrostatic discharge Electrostatic dischargeGrounding methods to prevent electrostatic discharge Acronyms and abbreviations Network access server Media Access ControlPower-On Self Test Local-area networkIndex Index