HP 441877-00F manual Adapter configurations

Page 37

•Locally Administered Address. Specifies the user-defined MAC Address of the adapter, which overrides the burned-in MAC Address. This box is disabled if the selected adapter has been teamed. o Default = Not Present

o Range: Value; Not Present

•Log Link State Event. Enables or disables the logging of link state changes. If enabled, a link up change event or a link down change event generates a message that is displayed in the system event logger.

o Default = Enabled

o Range = Disabled; Enabled

•Priority and VLAN. Enables or disables the ability to insert or remove the 802.1q tags for priority and VLAN.

o Default = Priority & VLAN Enabled

o Range = Priority & VLAN Disabled; Priority & VLAN Enabled; Priority Enabled; VLAN Enabled

•Receive Buffers. The size, in bytes, of the receive buffers that the hardware can support. This size is hardware-dependent and can include data buffers, buffer descriptors, and so on.

o Default = 256

•Smart Power Down. (NC110T, NC360x, and NC364T only) Minimizes power consumption by enabling the adapter to enter a deep sleep mode under certain conditions.

o Default = Hardware Default

o Range = Disabled; Enabled; Hardware Default

•TCP Checksum Offload (IPv4). Describes whether the device enabled or disabled the calculation of TCP Checksum over IPv4 packets.

o Default = Rx/Tx Enable

o Range = Disable; Tx Enable; Rx Enable; Rx/Tx Enable

•TCP Checksum Offload (IPv6). Describes whether the device enabled or disabled the calculation of TCP checksum over IPv6 packets.

o Default = Rx/Tx Enable

o Range = Disable; Tx Enable; Rx Enable; Rx/Tx Enable

•Transmit Buffers. The size, in bytes, of the transmit buffers that the hardware can support. This size is hardware-dependent and can include data buffers, buffer descriptors, and so forth.

o Default = 512 Bytes

•UDP Checksum Offload (IPv4). Describes whether the device enabled or disabled the calculation of UDP checksum over IPv4 packets.

o Default = Rx/Tx Enable

o Range = Disable; Tx Enable; Rx Enable; Rx/Tx Enable

•UDP Checksum Offload (IPv6). Describes whether the device enabled or disabled the calculation of UDP checksum over IPv6 packets.

o Default = Rx/Tx Enable

o Range = Disable; Tx Enable; Rx Enable; Rx/Tx Enable

•Wait for Link. Determines if the driver waits for auto-negotiation to be successful before reporting the link state. If disabled, the driver does not wait for auto-negotiation. If enabled, the driver does wait

Adapter configurations 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents HP ProLiant Network Adapter Software and Configuration Guide Audience assumptions Contents Technical support Supported adapters and operating systems OverviewOverview Adapter driver folders in HP SoftPaq Adapter driver and software informationDocumentation in the HP SoftPaq Installing network drivers new installations InstallationUninstall HP NC-Series NetXen 10GbE drivers Downloading filesWindows 2008 drivers Adapter support on WindowsWindows 2003 drivers Windows 2008 x64 driversWindows 2003 x64 drivers Windows 2000 driversAdapter support on NetWare Adapter support on LinuxParameter Options Description Jumbo = # Warning # Bind IPX Q571ESP NET=477A35BD Syntax SPURIOUS=n Where n = 0 or Balanceinterval Probeburstsize Smpmode Firmware upgrade utility HP NC-Series NetXen Online Firmware Upgrade Utility ROM HP NC-Series 10GbE Adapters Adapter configurationsProperty Parameter Configuring multiple NC510x PCIe 10 GbE adapters Boot options Configuring multiple ports on 10GbE adaptersAdapter configurations HP NC-Series Broadcom adapters TroubleshootingHP NC-Series Broadcom adapter properties Adapter configurations HP NC-Series Broadcom and Multifunction adapter properties Adapter configurations None. Disables checksum offloading HP NC-Series Intel adapter properties HP NC-Series Intel AdaptersAdapter configurations Adapter configurations HP NC-Series Intel adapter properties Adapter configurations Adapter configurations Boot Agent Network Boot PXE Preboot Configuration Possible values Description Settings Ibautil -option Parameter Description Ibautil -ALL -WOLDISABLE Adapter configurations Adapter configurations Adapter configurations NC31xx Fast Ethernet adapter properties HP NC-Series 31xx Fast Ethernet AdaptersAdapter configurations HP NC-Series NetXen 10GbE diagnostics DiagnosticsHP NC-Series Broadcom Multifunction adapter diagnostics Diagnostics Diagnostics HP NC-Series Broadcom adapter diagnostics Page Diagnostics Diagnostics HP NC-Series Intel adapter diagnostics Diagnostics Diagnostics Technical support Free automated customer support servicesBefore you contact HP HP contact informationHP FTP Server Acronyms and abbreviations Undi Index
Top Page Image Contents