Lennox International Inc SLP9801, XP2101 Cooling Airflow Settings, Heat Pump Airflow Settings

Page 41

Cooling Airflow Settings

Table 3. Adjustable Parameters Table (Installer)

Parameter Name

Default

Min.

Max.

Incr.

Dependency

Note	Installer entry

Cooling Airflow Settings

High Cooling Airflow (CFM @ 100% cool)

OU tons 400CFM

Min	Max	25
CFM	CFM

Min	Max	25
CFM	CFM

Outdoor Unit

present

1/2 HP blower

1 HP blower

Low Cooling Airflow (CFM @ lowest	(See Note 1	Min	Max	25	2+ stage Outdoor	1/2 HP blower
cool stage)	at end of	CFM	CFM		Unit present
	table)
	table)	Min	Max	25		1 HP blower
		Min	Max	25		1 HP blower
		CFM	CFM

Airflow Profile − Cooling	DIP SW	0	3	1	Outdoor Unit	0	A:ON:50%/30s,82% /
					present		7.5min OFF:50%/30s
						1	B:ON:82% / 7.5min; OFF:
							No delays
						2	C:ON: No delays; OFF:
							45sec delay
						3	D:No delays)

Heat Pump Airflow Settings

High Heat Pump Airflow (CFM @ 100%)

OU tons 400CFM

Min	Max	25
CFM	CFM

Min	Max	25
CFM	CFM

Heat Pump present

1/2 HP blower

1 HP blower

Low Heat Pump Airflow (CFM @	(See Note 2	Min	Max	25	2+ stage Heat Pump	1/2 HP blower
lowest stage)	at end of	CFM	CFM		present
	table)
	table)	Min	Max	25		1 HP blower
		Min	Max	25		1 HP blower
		CFM	CFM

table continued on next page

Page 41

icomfort Wi-Fit 7−Day Programmable Communicating Thermostat

Image 41

Contents icomfortt−Enabled Units INSTALLER’S SYSTEM SETUP GUIDE2P0912**P506920-01 CONTROLSPage Setting up typical icomfortt systemsTable of Contents Figure 1. icomfort by Lennoxt system SupportsOutdoor Temperature Sensor option Installation and Setup Figure 3. Settings change tools Change settingsDealer Number Figure 4. EnteringTable 1. System setting defaults and range Circulate fan ON time setting09 39 am Set time and dateFigure 5. View/edit time and date Figure 6. Set current time and dateFigure 7. Using the HUMIDITY CONTROL TIPS Add or Remove Non−communicating equipmentFigure 8. Add non−communicating device Add Non−Communicating Outdoor unitred settings SystemFigure 9. Add or remove non−communicating device 5a 5bSystem HumidifierSystem Figure 10. Add or remove non−communicating deviceDehumidifier DehumidifierFigure 11. Adjust communicating device screens Adjust a setting screen communicating devicesG71MPP or SLP98 Furnace Note Figure 12. Accessing device to modifyFigure 13. Modify device settings Figure 14. Adjust a non−communicating device setting Figure 15. Adjust a non−communicating device setting Figure 16. Adjust dehumidification when not using Humiditrol or an auxiliary dehumidifier DEHUMIDIFICATION modes Humidification and Dehumidification ModesHUMIDIFICATION modes Figure 17. Start testing screen Use the Tests / Diagnostics featuresFigure 18. Select tests to run screen Figure 19. Typical tests results screensSet up Equipment parameters Equipment, Alerts, DiagnosticsFigure 20. Testing finished screen Figure 21. Equipment parameters screenFigure 22. Edit equipment details Run DiagnosticsView and clear Installer Alerts Figure 23. Select device and run diagnosticsView cleared alerts Figure 25. Cleared alert confirmationFigure 24. Selecting and viewing alerts Figure 26. Cleared alerts screenSecure Connection Recommended Figure 27. Wi−Fi setupSTART HEREFigure 28. Change Networks Registering the icomfort Wi-FitthermostatRegistration for online access Figure 30. icomfort Wi-FitRegistration screen How Do I Upload a Skin? Welcome homeFigure 31. PC Welcome Screen Wi-FitTheryes no Access installer program from Home screenFigure 34. Re−configuration process Reconfigure a system2nd Stage Differential where applicable2 Rules for SSR Smooth Setback Recovery SSRHeat Pump Balance Points Heat Pump, Dual Fuel and Balance PointsLow Balance Point High Balance PointShut down HP Gas Heat Control Mode Figure 36. Variable Capacity Operation Flow ChartTable 2. Variable Capacity Furnace Operation Staged operationLoad−tracking Variable Capacity FAQs SLP98V only Installer entry Table 3. Adjustable Parameters Table InstallerLock in 2nd stage HP by Outdoor Temp Table 3. Adjustable Parameters Table InstallerAIR HANDLER Table 3. Adjustable Parameters Table InstallerFURNACE Gas Heat Airflow SettingsTable 3. Adjustable Parameters Table Installer Table 3. Adjustable Parameters Table Installer Cooling Airflow SettingsHeat Pump Airflow Settings Table 3. Adjustable Parameters Table Installer Other ParametersTable 4. Adjustable Parameters Table User Filter 1 Timer Table 5. Alert Codes and Troubleshooting Alert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingTable 5. Alert Codes and Troubleshooting Homeowner Service Alert Codes8Issue / Problem Table 6. Troubleshooting TipsPossible Cause Corrective Action / CommentsHigh Balance Point and Low Bal Table 6. Troubleshooting TipsDetermine the actual Software ver Table 6. Troubleshooting TipsDuring the cooling mode the dis Table 6. Troubleshooting Tipsicomfortt Communicating System Wiring Wiring Diagramsicomfort by Lennoxt AIR HANDLER AHC Wiring Diagramsfor use with any icomfort by Lennoxt system Optional Accessories WiringLVCS Ventilation Control System Optional Accessories Wiringfor use with any icomfort by Lennoxt system attached to the PUSHBUTTON TIPS Setting up typical systemsTIPS TIPS Setting up typical systemsT PUMP DUAL FUELTIPS TIPS Setting up typical systemsTIPS TIPS Setting up typical systemsT PUMP UNITSTIPS REVISION HISTORY Table 7. Replacement Controlsicomfortt−Enabled Unit Replacement Kit Catalog No