Lennox International Inc G71MPP03, XP2101 Other Parameters, Adjustable Parameters Table Installer

Page 42

Other Parameters

Table 3. Adjustable Parameters Table (Installer)

Parameter Name	Default	Min.	Max.	Incr.	Dependency	Note	Installer entry

Other Parameters

Equipment Name	Furnace	N/A	N/A	N/A	None	Up to 35 characters

Continuous Indoor Blower Airflow	DIP SW (See	Min	Max	25	None	1/2 HP blower
	Note 3 at	CFM	CFM
	end of table)
	end of table)	Min	Max	25		1 HP blower
		Min	Max	25		1 HP blower
		CFM	CFM

Humidification Airflow	Same as	Min	Max	25	Humidifier present	1/2 HP blower
	above	CFM	CFM

		Min	Max	25		1 HP blower
		CFM	CFM

Dehumidification Airflow Percentage

140

(=70%)

120	160	2	OU present and SC	Percent of High Cooling
(=60%)	(=80%)	(=1%)	(Subnet Controller)	Airflow
			algorithm support

Note 1: Minimum Outdoor Unit Cooling Stage as a percentage of High Cooling Airflow (value is rounded up to the closest number on 25 CFM resolution.

Note 2: Minimum Outdoor Unit Heating Stage as a percentage of High Heat Pump Airflow (value is rounded up to the closest number on 25 CFM resolution).

Note 3: All communicating Installer Parameters default CFM values based on DIP switch setting (non−communicating value) are calculated using the CFM conversion tables and rounded up to closest number on 25 CFM resolution.

Note 4: Parameter dependency − Certain parameters are dependent on others and may not be shown on the display.

Note 5: Default Values − Jumper/DIP switches impact the default value of some parameters.

506920−01 09/12

Page 42

Image 42

Contents 2P0912**P506920-01 INSTALLER’S SYSTEM SETUP GUIDEicomfortt−Enabled Units CONTROLSSetting up typical icomfortt systems Table of ContentsPage Supports Outdoor Temperature Sensor optionFigure 1. icomfort by Lennoxt system Installation and Setup Dealer Number Change settingsFigure 3. Settings change tools Figure 4. EnteringCirculate fan ON time setting Table 1. System setting defaults and rangeFigure 5. View/edit time and date Set time and date09 39 am Figure 6. Set current time and dateFigure 7. Using the Add or Remove Non−communicating equipment HUMIDITY CONTROL TIPSred settings Add Non−Communicating Outdoor unitFigure 8. Add non−communicating device SystemSystem 5a 5bFigure 9. Add or remove non−communicating device HumidifierDehumidifier Figure 10. Add or remove non−communicating deviceSystem DehumidifierAdjust a setting screen communicating devices Figure 11. Adjust communicating device screensFigure 12. Accessing device to modify Figure 13. Modify device settingsG71MPP or SLP98 Furnace Note Figure 14. Adjust a non−communicating device setting Figure 15. Adjust a non−communicating device setting Figure 16. Adjust dehumidification when not using Humiditrol or an auxiliary dehumidifier Humidification and Dehumidification Modes HUMIDIFICATION modesDEHUMIDIFICATION modes Figure 18. Select tests to run screen Use the Tests / Diagnostics featuresFigure 17. Start testing screen Figure 19. Typical tests results screensFigure 20. Testing finished screen Equipment, Alerts, DiagnosticsSet up Equipment parameters Figure 21. Equipment parameters screenRun Diagnostics Figure 22. Edit equipment detailsFigure 23. Select device and run diagnostics View and clear Installer AlertsFigure 24. Selecting and viewing alerts Figure 25. Cleared alert confirmationView cleared alerts Figure 26. Cleared alerts screenSTART Figure 27. Wi−Fi setupSecure Connection Recommended HERERegistering the icomfort Wi-Fitthermostat Registration for online accessFigure 28. Change Networks Figure 30. icomfort Wi-FitRegistration screen Figure 31. PC Welcome Screen Welcome homeHow Do I Upload a Skin? Wi-FitTherAccess installer program from Home screen yes noReconfigure a system Figure 34. Re−configuration process2nd Stage Differential where applicable2 Smooth Setback Recovery SSR Rules for SSRLow Balance Point Heat Pump, Dual Fuel and Balance PointsHeat Pump Balance Points High Balance PointShut down HP Figure 36. Variable Capacity Operation Flow Chart Gas Heat Control ModeStaged operation Table 2. Variable Capacity Furnace OperationLoad−tracking Variable Capacity FAQs SLP98V only Table 3. Adjustable Parameters Table Installer Installer entryTable 3. Adjustable Parameters Table Installer Lock in 2nd stage HP by Outdoor TempTable 3. Adjustable Parameters Table Installer AIR HANDLERGas Heat Airflow Settings Table 3. Adjustable Parameters Table InstallerFURNACE Cooling Airflow Settings Heat Pump Airflow SettingsTable 3. Adjustable Parameters Table Installer Other Parameters Table 3. Adjustable Parameters Table InstallerTable 4. Adjustable Parameters Table User Filter 1 Timer Table 5. Alert Codes and Troubleshooting Table 5. Alert Codes and Troubleshooting AlertTable 5. Alert Codes and Troubleshooting AlertTable 5. Alert Codes and Troubleshooting AlertTable 5. Alert Codes and Troubleshooting AlertTable 5. Alert Codes and Troubleshooting AlertTable 5. Alert Codes and Troubleshooting AlertTable 5. Alert Codes and Troubleshooting AlertTable 5. Alert Codes and Troubleshooting AlertHomeowner Service Alert Codes8 Table 5. Alert Codes and TroubleshootingPossible Cause Table 6. Troubleshooting TipsIssue / Problem Corrective Action / CommentsTable 6. Troubleshooting Tips High Balance Point and Low BalTable 6. Troubleshooting Tips Determine the actual Software verTable 6. Troubleshooting Tips During the cooling mode the disWiring Diagrams icomfortt Communicating System WiringWiring Diagrams icomfort by Lennoxt AIR HANDLER AHCOptional Accessories Wiring for use with any icomfort by Lennoxt systemOptional Accessories Wiring for use with any icomfort by Lennoxt systemLVCS Ventilation Control System attached to the PUSHBUTTON Setting up typical systems TIPSTIPS Setting up typical systemsT PUMP DUAL FUEL TIPSTIPS Setting up typical systems TIPSTIPS Setting up typical systemsT PUMP UNITS TIPSTIPS icomfortt−Enabled Unit Table 7. Replacement ControlsREVISION HISTORY Replacement Kit Catalog No