Lennox International Inc SL28003, XP2101 Set time and date, 09 39 am, View/edit time and date

Page 7

Set time and date

Set time and date

Use the arrows to select Time and Date; press edit (see figure 5) to proceed to the ).

When Time and Date" screen (figure 6) appears, enter the correct date as follows:

system settings Time and Date Daylight Saving Time Circulate Fan ON Time System Name Dealer Number Dealer Name

Dealer Address

Dealer Phone

Dealer Email

Dealer Website

9:39 am Aug 15, 2012

To adjust a setting, highlight it, then press Edit

current value:

9:39 am Aug 15, 2012

edit

back next

SUse the left and right arrows to change the month and year.

STouch a day of the month to select it.

SPress on the hour or minute; up down arrows appear to allow change.

STouch the am/pm field to toggle it between am and pm.

SWhen the correct date and time is set, press save to save settings and return to previous settings screen.

Touch next to continue to next screen.

system settings
		January 2012
S	M	T	W	T	F	S
1	2	3	4	5	6	7	09 : 39 am
8	9	10	11	12	13	14

Figure 5. View/edit time and date

15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30	31				save

9:39 am Aug 15, 2012

Figure 6. Set current time and date

Page 7

icomfort Wi-Fit 7−Day Programmable Communicating Thermostat

Image 7

Contents CONTROLS INSTALLER’S SYSTEM SETUP GUIDEicomfortt−Enabled Units 2P0912**P506920-01Table of Contents Setting up typical icomfortt systemsPage Outdoor Temperature Sensor option SupportsFigure 1. icomfort by Lennoxt system Installation and Setup Figure 4. Entering Change settingsFigure 3. Settings change tools Dealer NumberTable 1. System setting defaults and range Circulate fan ON time settingFigure 6. Set current time and date Set time and date09 39 am Figure 5. View/edit time and dateFigure 7. Using the HUMIDITY CONTROL TIPS Add or Remove Non−communicating equipmentSystem Add Non−Communicating Outdoor unitFigure 8. Add non−communicating device red settingsHumidifier 5a 5bFigure 9. Add or remove non−communicating device SystemDehumidifier Figure 10. Add or remove non−communicating deviceSystem DehumidifierFigure 11. Adjust communicating device screens Adjust a setting screen communicating devicesFigure 13. Modify device settings Figure 12. Accessing device to modifyG71MPP or SLP98 Furnace Note Figure 14. Adjust a non−communicating device setting Figure 15. Adjust a non−communicating device setting Figure 16. Adjust dehumidification when not using Humiditrol or an auxiliary dehumidifier HUMIDIFICATION modes Humidification and Dehumidification ModesDEHUMIDIFICATION modes Figure 19. Typical tests results screens Use the Tests / Diagnostics featuresFigure 17. Start testing screen Figure 18. Select tests to run screenFigure 21. Equipment parameters screen Equipment, Alerts, DiagnosticsSet up Equipment parameters Figure 20. Testing finished screenFigure 22. Edit equipment details Run DiagnosticsView and clear Installer Alerts Figure 23. Select device and run diagnosticsFigure 26. Cleared alerts screen Figure 25. Cleared alert confirmationView cleared alerts Figure 24. Selecting and viewing alertsHERE Figure 27. Wi−Fi setupSecure Connection Recommended STARTRegistration for online access Registering the icomfort Wi-FitthermostatFigure 28. Change Networks Figure 30. icomfort Wi-FitRegistration screen Wi-FitTher Welcome homeHow Do I Upload a Skin? Figure 31. PC Welcome Screenyes no Access installer program from Home screenFigure 34. Re−configuration process Reconfigure a system2nd Stage Differential where applicable2 Rules for SSR Smooth Setback Recovery SSRHigh Balance Point Heat Pump, Dual Fuel and Balance PointsHeat Pump Balance Points Low Balance PointShut down HP Gas Heat Control Mode Figure 36. Variable Capacity Operation Flow ChartTable 2. Variable Capacity Furnace Operation Staged operationLoad−tracking Variable Capacity FAQs SLP98V only Installer entry Table 3. Adjustable Parameters Table InstallerLock in 2nd stage HP by Outdoor Temp Table 3. Adjustable Parameters Table InstallerAIR HANDLER Table 3. Adjustable Parameters Table InstallerTable 3. Adjustable Parameters Table Installer Gas Heat Airflow SettingsFURNACE Heat Pump Airflow Settings Cooling Airflow SettingsTable 3. Adjustable Parameters Table Installer Table 3. Adjustable Parameters Table Installer Other ParametersTable 4. Adjustable Parameters Table User Filter 1 Timer Table 5. Alert Codes and Troubleshooting Alert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingAlert Table 5. Alert Codes and TroubleshootingTable 5. Alert Codes and Troubleshooting Homeowner Service Alert Codes8Corrective Action / Comments Table 6. Troubleshooting TipsIssue / Problem Possible CauseHigh Balance Point and Low Bal Table 6. Troubleshooting TipsDetermine the actual Software ver Table 6. Troubleshooting TipsDuring the cooling mode the dis Table 6. Troubleshooting Tipsicomfortt Communicating System Wiring Wiring Diagramsicomfort by Lennoxt AIR HANDLER AHC Wiring Diagramsfor use with any icomfort by Lennoxt system Optional Accessories Wiringfor use with any icomfort by Lennoxt system Optional Accessories WiringLVCS Ventilation Control System attached to the PUSHBUTTON TIPS Setting up typical systemsTIPS TIPS Setting up typical systemsT PUMP DUAL FUELTIPS TIPS Setting up typical systemsTIPS TIPS Setting up typical systemsT PUMP UNITSTIPS Replacement Kit Catalog No Table 7. Replacement ControlsREVISION HISTORY icomfortt−Enabled Unit