Agilent Technologies E3631A - page 31

Chapter 2 Quick Start

To use the power supply in constant voltage mode

30

5 Adjust the knob for the desired current limit. 1

Check that the Lmt annunciator still blinks. Set the knob for current control.

The second digit of ammeter will be blinking. Adjust the knob to the desired

current limit.

6 Adjust the knob for the desired output voltage. 1

Set the knob for voltage control. The second digit of the voltmeter will be

blinking. Adjust the knob to the desired output voltage.

7 Return to the meter mode.

key or let the display time-out after several seconds to return

to the meter mode. Notice that the Lmt annunciator turns off and the display

returns to the meter mode. In the meter mode, the display shows the actual

output voltage and current of the selected supply.

8 Verify that the power supply is in the constant voltage mode.

If you operate the +6V supply in the constant voltage (CV) mode, verify that

CV and +6V annunciators are lit. If you operate the power supply for +25V

supply or -25V supply, the +25V or -25V annunciator will turn on. If the CC

annunciator is lit, choose a higher current limit.

Note During actual CV operation, if a load change causes the current limit to be

exceeded, the power supply will automatically crossover to constant current

mode at the preset current limit and the output voltage will drop

proportionately.

1You can use the resolution selection keys to move the blinking digit to the right or

left when setting the voltage and current.

Vol/Cur

Vol/Cur

Display Limit

Display Limit

Contents

Main Page The Front Panel at a Glance 3 Front-Panel Voltage and Current Settings 5 Display Annunciators To review the display annunciators, hold down key as you turn on the power supply. The Rear Panel at a Glance In This Book Page Page Page Page Page Page Page Performance Specifications Page Supplemental Characteristics Chapter 1 Specifications Supplemental Characteristics 18 Page Page Page Quick Start To prepare the power supply for use Page To check the rated voltages of the power supply Page To check the rated currents of the power supply Page To use the power supply in constant voltage mode Page To use the power supply in constant current mode Page To use the power supply in track mode To store and recall the instrument state Store 1 Store 3 done recall 1 done recall 3 To rack mount the power supply Page Page Page Calibration Procedures Agilent Technologies Calibration Services Calibration Interval Automating Calibration Procedures Recommended Test Equipment Test Considerations Performance Verification Tests Self-Test Performance Verification Tests Measurement Techniques Setup for Most Tests Electronic Load General Measurement Techniques Current-Monitoring Resistor Programming Voltage and Current Values Constant Voltage (CV) Verifications Constant Voltage Test Setup Voltage Programming and Readback Accuracy Page CV Load Regulation CV Line Regulation Normal Mode Voltage Noise (CV Ripple and Noise) Common Mode Current Noise Load Transient Response Time Constant Current (CC) Verifications Constant Current Test Setup Current Programming and Readback Accuracy Page CC Load Regulation CC Line Regulation Normal Mode Current Noise (CC Ripple and Noise) Performance Test Record for Agilent E3631A 59 Performance Test Record for Agilent E3631A CV Performance Test Record Test Description Actual Result Specifications Upper Limit Lower Limit Performance Test Record for Agilent E3631A CC Performance Test Record Test Description Actual Result Specifications Upper Limit Lower Limit Calibration Security Code To Unsecure the Power Supply for Calibration secured 000000 code 003631 code unsecured To Unsecure the Power Supply Without the Security Code Calibration Count Calibration Message General Calibration/Adjustment Procedure cal mode cal setup 1 v lo +0.1 11 1000 v v lo +0.0860 v v hi +5.7000v v hi +5.9990v cal setup 2 i lo +0.100 a i lo +0.099 a i hi +4.750 a i hi +4.999 a cal setup 3 Aborting a Calibration in Progress Calibration Record for Agilent E3631A 72 Calibration Record for Agilent E3631A Step Calibration Description Measurement Mode (DVM) Supply being Adjusted Error Messages Page 75 Calibration Program 76 ...continued 77 ...continued Page Page Theory of Operation Block Diagram Overview Page AC Input and Bias Supplies Floating Logic Page D-to-A Converter A-to-D Converter Power Mesh and Control Page Earth-Referenced Logic Front Panel Page Service Operating Checklist Is the Power Supply Inoperative? Does the Power Supply Fail Self-Test? Types of Service Available Standard Repair Service (worldwide) Express Exchange (U.S.A. only) Repacking for Shipment Electrostatic Discharge (ESD) Precautions Surface Mount Repair To Replace the Power-Line Fuse Troubleshooting Hints Unit is Inoperative Unit Reports Errors 740 to 748 Unit Fails Self-Test Bias Supplies Problems Self-Test Procedures Power-On Self-Test Complete Self-Test Page Page Page Page 104 Replaceable Parts To Order Replaceable Parts 1 2 3 Backdating and Part Changes E3631-60002 Top PCB Assembly Page Page Page Page Page E3631-60003 VFD Assembly 111 E3631-60003 VFD Assembly E3631-60004 Bottom PCB Assembly Page Page Page E3631-60005 Front Frame Assembly 116 E3631-60005 Front Frame Assembly E3631-60005 Power SupplyAssembly Manufacturers List 117 Manufacturers List Page Page Page Page Schematics Page Page Page Page Page Page Page Page Page Page !