Omega Speaker Systems FPU5-MT-220, FPU5-MT-110 manual ML Per Revolution

Page 77

Specifications

9

 

 

 

Table 9-6. Average Flow Rates For Viscous Liquids

 

 

 

 

 

 

 

Tubing Wall

Tubing Size

 

 

Liquid

Thickness

Inner Diameter

mL Per Revolution

Viscosity

Mineral Oil

1⁄16"

1⁄32"

0

400 cps

Mineral Oil

1⁄16"

1⁄16"

0.005

400 cps

Mineral Oil

1⁄16"

1⁄8"

0.04

400 cps

Mineral Oil

1⁄16"

3⁄16"

0.15

400 cps

Mineral Oil

1⁄16"

1⁄4"

0.20

400 cps

Mineral Oil

1⁄16"

5⁄16"

0.25

400 cps

Molasses

1⁄16"

1⁄32"

0

8,000 cps

Molasses

1⁄16"

1⁄16"

0.002

8,000 cps

Molasses

1⁄16"

1⁄8"

0.01

8,000 cps

Molasses

1⁄16"

3⁄16"

0.07

8,000 cps

Molasses

1⁄16"

1⁄4"

0.08

8,000 cps

Molasses

1⁄16"

5⁄16"

0.10

8,000 cps

Flow Rate Tests were done with 20°C liquids at 0 psi back pressure.

9-5

Page 76 Page 78
Image 77
Page 76 Page 78
Contents User’s Guide Servicing North America Unpacking Instructions Table of Peristaltic Pump Motor Peristaltic Pump Motor Chapter Specifications Spare Parts and Accessories 10-1Peristaltic Pump Motor RPM IndexIndex III Description FeaturesIntroduction Introduction Front View Parts of the Pump MotorFront View Description FunctionLeft Side View Left Side ViewRight Side View Right Side ViewMembrane Keypad Detail Membrane Keypad and DisplayFlow Rate key Membrane Keypad Details cont’dRear View Rear ViewUP and Down Arrow Keys Scrolling Limits Language Button Rear View cont’dParts of the Pump Motor Getting Started Pump Motor Mounting Configurations Number of Pumps onAttaching the Pump IntroductionRefer to Figures 3-1 through Attaching a Single Pump Directly to the MotorPlacing the Second Pump on Top of the First Pump Stacking Two Pumps on One Side of the MotorLoading the Tubing Selecting TubingTubing Life See .2 to set the pumping direction Getting Started Using the ON/OFF Switch Turning on the PowerStopped Display Mode Introduction to the Two Display ModesStopped vs. Running Display Modes Running Display ModeDisplaying Pump Messages in Five Different Languages Stopped Display ModeOperating the Pump Motor Régler LA QTÉ English French Spanish German ItalianDefining the Direction of Pumping Left Pump Right Pump Selecting the Tubing Inner DiameterTube Inner Diameters English Metric Calibrating the Tubing Priming the TubingOperating the Pump Motor in the Stopped Display Mode Tips for Optimum Calibration Accuracy Preparing for Pumping in a Specific Mode Measuring the Temperature of a FluidTotal Volume Pumping in the RPM Mode Running Display ModeRPM Mode Shows the range of the RPM numbers you can work with RPM Mode Cont’d Pumping in the Flow Rate Mode Flow Rate ModeShows the ranges allowed for the various tubing sizes Flow Rate Ranges cont’d Display Xxx mL/min Flow Rate Mode Flow Rate Mode Pumping in the Time Mode Time ModeTime Range Display Xxxxxx Time Mode Time Mode Block Diagram Pumping in the Total Volume Mode Total Volume ModeTotal Volume Range Pumping in the Total Volume ModeOperating the Pump Motor in the Running Display Mode Total Volume Mode Cont’d Auxiliary Out Remote Monitor Preventing Tubing from Moving During Pump OperationOther Pumping Options Auxiliary In Remote Start/Stop 500Ω LEDDisplay Error Messages Troubleshooting GuideError Message Problem SolutionRunning Display Mode and try to select the command again Error MessageLocked Rotor? Overcurrent Press the Total Volume key Short Circuit? Error Message Stopped Display Mode and refer to Section Other Pumping ProblemsProblem Solution Another pump, if necessary Troubleshooting Guide Maintenance Design SolutionTechnical Details Theory of OperationTechnical Details Calibration Accuracy SpecificationsMotor Average Flow RatesTubing Materials SpeedAverage Tubing Life ⁄32 300 ⁄16 250 100 ML Per Revolution Specifications Accessories Spare Parts and AccessoriesSpare Parts Part Number DescriptionAccessories cont’d Peristatic Pump 10-4 WARRANTY/DISCLAIMER
Top Page Image Contents