Omega Speaker Systems FPU5-MT-110, FPU5-MT-220 manual Defining the Direction of Pumping

Page 30

Operating the Pump Motor in the STOPPED Display Mode	5

5.2 Defining the Direction of Pumping

INLET

SELECT

Display shows

<no change>

ACTION

LEDs indicate new

pump direction

The INLET SELECT key, left and right pump icons, and green LEDs define the direction of pumping by specifying the tubing inlets and outlets.

1.Refer to Figure 5-1.

2.To determine the direction of pumping, look at the left and right pump icons and green LEDs. Only one of each pair of LEDs is lit. The lit LED points to the tubing inlet.

NOTE

A top tubing inlet on the left pump corresponds to a bottom tubing inlet on the right pump and vice versa.

Two pumps stacked on one side of the motor will pump fluid in the same direction. Two pumps mounted on opposite sides of the motor will pump fluid in opposing directions.

5-3

Image 30

Contents User’s Guide Servicing North America Unpacking Instructions Table of Peristaltic Pump Motor Chapter Specifications Spare Parts and Accessories 10-1 Peristaltic Pump MotorPeristaltic Pump Motor Index RPMIndex III Features IntroductionDescription Introduction Front View Parts of the Pump MotorFront View Description FunctionLeft Side View Left Side ViewRight Side View Right Side ViewMembrane Keypad and Display Membrane Keypad DetailMembrane Keypad Details cont’d Flow Rate keyRear View UP and Down Arrow Keys Scrolling LimitsRear View Rear View cont’d Language ButtonParts of the Pump Motor Attaching the Pump Pump Motor Mounting Configurations Number of Pumps onGetting Started IntroductionAttaching a Single Pump Directly to the Motor Refer to Figures 3-1 throughStacking Two Pumps on One Side of the Motor Placing the Second Pump on Top of the First PumpSelecting Tubing Tubing LifeLoading the Tubing See .2 to set the pumping direction Getting Started Stopped Display Mode Turning on the PowerUsing the ON/OFF Switch Introduction to the Two Display ModesRunning Display Mode Stopped vs. Running Display ModesStopped Display Mode Operating the Pump MotorDisplaying Pump Messages in Five Different Languages English French Spanish German Italian Régler LA QTÉDefining the Direction of Pumping Selecting the Tubing Inner Diameter Left Pump Right PumpTube Inner Diameters English Metric Priming the Tubing Calibrating the TubingOperating the Pump Motor in the Stopped Display Mode Tips for Optimum Calibration Accuracy Measuring the Temperature of a Fluid Preparing for Pumping in a Specific ModeTotal Volume Running Display Mode RPM ModePumping in the RPM Mode Shows the range of the RPM numbers you can work with RPM Mode Cont’d Flow Rate Mode Pumping in the Flow Rate ModeShows the ranges allowed for the various tubing sizes Flow Rate Ranges cont’d Display Xxx mL/min Flow Rate Mode Flow Rate Mode Time Mode Pumping in the Time ModeTime Range Display Xxxxxx Time Mode Time Mode Total Volume Mode Block Diagram Pumping in the Total Volume ModePumping in the Total Volume Mode Total Volume RangeOperating the Pump Motor in the Running Display Mode Total Volume Mode Cont’d Preventing Tubing from Moving During Pump Operation Other Pumping OptionsAuxiliary Out Remote Monitor 500Ω LED Auxiliary In Remote Start/StopError Message Problem Troubleshooting GuideDisplay Error Messages SolutionError Message Running Display Mode and try to select the command againLocked Rotor? Overcurrent Press the Total Volume key Short Circuit? Error Message Other Pumping Problems Stopped Display Mode and refer to SectionProblem Solution Another pump, if necessary Troubleshooting Guide Technical Details Design SolutionMaintenance Theory of OperationTechnical Details Specifications Calibration AccuracyTubing Materials Average Flow RatesMotor SpeedAverage Tubing Life ⁄32 300 ⁄16 250 100 ML Per Revolution Specifications Spare Parts Spare Parts and AccessoriesAccessories Part Number DescriptionAccessories cont’d Peristatic Pump 10-4 WARRANTY/DISCLAIMER