Omega Speaker Systems FPU5-MT-110, FPU5-MT-220 manual Locked Rotor?

Page 62

Troubleshooting Guide	7

Error Message

Problem

Solution

Locked Rotor?	B
(continued)	There may be an internal problem.

B

For internal problems, call Customer Service.

Lost PHASE SYNC!	There may be an internal problem. 1.	Turn the unit’s power off and
		on, adjust the settings, and
		attempt to resume pumping.
	2.	If the problem persists, call
		Customer Service.

Must SET RPM!	A
	You have attempted to pump in
	the RPM Mode with the RPM
	set to 0 rpm.

A

1.Press the RPM key.

2.Use the UP and DOWN ARROW keys to adjust the RPM setting.

3.Press the START/STOP key to start the pump.

B

You have attempted to dispense fluid during calibration with the RPM set to 0 rpm.

B

1.Press the RPM key.

2.Use the UP and DOWN ARROW keys to adjust the RPM setting.

3.Press the CALIBRATE key to restart the calibration.

Must SET TIME!	You have attempted to
	pump in the TIME
	Mode with the TIME set
	to 00:00:00.

1.Press the TIME key.

2.Toggle from SECONDS to MINUTES to HOURS with the TIME key.

3.Use the UP and DOWN ARROW keys to adjust the TIME setting.

4.Press the START/STOP key to start the pump.

.

7-3

Image 62

Contents User’s Guide Servicing North America Unpacking Instructions Table of Peristaltic Pump Motor Chapter Specifications Spare Parts and Accessories 10-1 Peristaltic Pump MotorPeristaltic Pump Motor Index RPMIndex III Description FeaturesIntroduction Introduction Front View Parts of the Pump MotorFront View Description FunctionLeft Side View Left Side ViewRight Side View Right Side ViewMembrane Keypad and Display Membrane Keypad DetailMembrane Keypad Details cont’d Flow Rate keyRear View Rear ViewUP and Down Arrow Keys Scrolling Limits Rear View cont’d Language ButtonParts of the Pump Motor Attaching the Pump Pump Motor Mounting Configurations Number of Pumps onGetting Started IntroductionAttaching a Single Pump Directly to the Motor Refer to Figures 3-1 throughStacking Two Pumps on One Side of the Motor Placing the Second Pump on Top of the First PumpLoading the Tubing Selecting TubingTubing Life See .2 to set the pumping direction Getting Started Stopped Display Mode Turning on the PowerUsing the ON/OFF Switch Introduction to the Two Display ModesRunning Display Mode Stopped vs. Running Display ModesDisplaying Pump Messages in Five Different Languages Stopped Display ModeOperating the Pump Motor English French Spanish German Italian Régler LA QTÉDefining the Direction of Pumping Selecting the Tubing Inner Diameter Left Pump Right PumpTube Inner Diameters English Metric Priming the Tubing Calibrating the TubingOperating the Pump Motor in the Stopped Display Mode Tips for Optimum Calibration Accuracy Measuring the Temperature of a Fluid Preparing for Pumping in a Specific ModeTotal Volume Pumping in the RPM Mode Running Display ModeRPM Mode Shows the range of the RPM numbers you can work with RPM Mode Cont’d Flow Rate Mode Pumping in the Flow Rate ModeShows the ranges allowed for the various tubing sizes Flow Rate Ranges cont’d Display Xxx mL/min Flow Rate Mode Flow Rate Mode Time Mode Pumping in the Time ModeTime Range Display Xxxxxx Time Mode Time Mode Total Volume Mode Block Diagram Pumping in the Total Volume ModePumping in the Total Volume Mode Total Volume RangeOperating the Pump Motor in the Running Display Mode Total Volume Mode Cont’d Auxiliary Out Remote Monitor Preventing Tubing from Moving During Pump OperationOther Pumping Options 500Ω LED Auxiliary In Remote Start/StopError Message Problem Troubleshooting GuideDisplay Error Messages SolutionError Message Running Display Mode and try to select the command againLocked Rotor? Overcurrent Press the Total Volume key Short Circuit? Error Message Other Pumping Problems Stopped Display Mode and refer to SectionProblem Solution Another pump, if necessary Troubleshooting Guide Technical Details Design SolutionMaintenance Theory of OperationTechnical Details Specifications Calibration AccuracyTubing Materials Average Flow RatesMotor SpeedAverage Tubing Life ⁄32 300 ⁄16 250 100 ML Per Revolution Specifications Spare Parts Spare Parts and AccessoriesAccessories Part Number DescriptionAccessories cont’d Peristatic Pump 10-4 WARRANTY/DISCLAIMER