Samsung AS30UGBNUMG, AQ36UGBNUMG, AS36UGBNUMG, AQ36UGBXUMG Purging the connected pipes, AQseries

Page 36

InstallAA ing and connecting the drain hose of the outdoor unit

(AQseries)

While heating, ice may accumulate. During the process of defrosting, check if condensation draining is adequate. For adequate draining, do the following:

1. Insert the drain plug into the drain hole on the underside of the outdoor unit.

• To avoid drain plug from contacting the ground, secure gap between the ground and the bottom surface of the outdoor unit.

 

Drain hole

Drain plug

 

 

2. Connect a drain hose to the drain plug.

Bottom surface of outdoor unit

 

Drain hole

 

 

Drain plug

Drain hose

3. Ensure that condensation draining is adequate.

 

Snow-proof hood

 

 

• In areas with heavy snow fall, piled snow could block the air intake.

 

 

To avoid this incident, install a frame that is higher than estimated snow

 

 

fall. In addition, install a snow-proof hood to avoid snow from piling on the

 

outdoor unit.

Estimated

 

snow fall Frame

 

 

Ground

Purging the connected pipes

The outdoor unit is loaded with sufficient R-22 refrigerant .You should purge the air in the indoor unit and in the pipe.If air remains in the refrigerant pipes, it affects the compressor. It may cause reduction of cooling capacity and malfunction.

• When installing, make sure there is no leakage. When recovering the refrigerant, ground the compressor first before removing the connection pipe. If the refrigerant pipe is not properly connected and the compressor works with the service valve open, the pipe inhales the air and it makes the pressure inside of the refrigerant cycle abnormally high. It may cause explosion and injury.

1.

Connect each assembly pipe to the appropriate valve on the outdoor unit and Outdoor unit

Indoor unit

 

tighten the flare nut.

 

 

 

 

 

 

Gas pipe side

 

 

2.

Tighten the flare nut first with your hands, and then with a torque wrench,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Liquid pipe side

 

 

 

applying the following torque:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

36

MAX4 AQ&AST&U_IB&IM_DB98-34063A_E.indd 36

2013-3-18 15:46:40

Image 36
Contents English Contents SafetAA y precautions Important safety symbols and precautionsFollow directions Wall socketFor Using For Cleaning ChecAA king before use Operation rangesPower ChecAA king the name of the partsMain parts  AQ/AS 30/32/36T  Display  AQ/AS 30/32/36TChecAA king the remote controller Remote controller buttonsRemote controller display Battery changing timeStoring the remote controller Inserting the batteriesBasicAA function Press the button to adjust the temperature Press the button to set the desired fan speedUsing the Turbo function Press the Air swing button on the remote controllerAdjusA ting the air flow direction Vertical air flowAA mode Press the button on the remote controllerPress the Time Up or Time Down button to set the time Press the Set button to active it onSettinAA g the On/Off timer Press the On Timer/Off Timer buttonAdditional options available in On timer mode Using the Smart Saver function From the moment you have set the timerIf the air conditioner is on If the air conditioner is off Turn off automaticallyUsingAA the Auto Clean function Using the Quiet functionWhen the air conditioner is turned on 30/32/36T 30/32/36UCleaning the indoor unit Cleaning the outdoor unit heat exchangerOpening the panel Heat exchangerCleanAA ing the air conditioner Cleaning the air filterRemoving the Air filter Open the panel and put the Air filter outAACleaning the air conditioner Bio filterBio filter sky-blue Deodorizing filter Deodorizing filter blackMainAA taining the air conditioner Periodical checksTroubleshootingAA Flow movement changes. It is normal ConnectionSafety precautions General informationChoosing the installation location Installing the unitPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyChooAA sing the installation location Where sulfide gas existsOutdoor Unit When installing more than 1 outdoor unit When the air outlet is towards the wall Figure Description Top view Side viewAccessories Accessories in the indoor unit caseAccessories in the outdoor unit case Fixing the installation plate Optional accessoriesTools required for installation General Tools Tools for test operationsConnecting the assembly cable Cable specificationConnecting the cable Extend the assembly cable if necessary Each wire is labeled with the corresponding terminal numberInstallation Smooth the cut edges Cut off the remaining foam insulationAAPurging the indoor unit Cutting or extending the pipeUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flareCuttingAA or extending the pipe Outer DiameterDrain hose installation Two hoses are firmly connected, there is no water leakageHose tight Check for leakage on both side of the drain outletPurging the connected pipes AQseriesAdding Refrigerant Add refrigerant charge according to table belowIf you use a pipe shorter than 4 30/32 or 5 36 m Purge time is normalPerfoAA rming the gas leak tests Fixing the indoor unit in placeOutdoor unit installed on the wall by rack Fixing the outdoor unit in placeAppropriate support wall or ground ModelPress the Power button and check the following Press the Power button to stop the operationFinalAA Check and Trial Operation Check the followingsApply heat to the contraction tube to contract it After tube contraction work is completed, wrap it withInsulation tape to finish AATechnical Specifications AS36UGBUMG AS30UGBUMGEnglish Questions or COMMENTS? EgyptAir Conditioner