Samsung AS36UGBNXSG, AQ36UGBNUMG, AS30UGBNUMG Fixing the installation plate, Optional accessories

Page 29

Optional accessories

The following connection accessories are optional. If they are not supplied, you should obtain them before installing the air conditioner.

Insulated Assembly

Insulated Assembly

Insulated Assembly Pipe,

Insulated Assembly Pipe, Ø15.88/

PE T3 Foam

 

Drain Plug (1)

Pipe, Ø6.35mm (1)

Pipe, Ø9.52mm (1)

Ø15.88mm (1)

Ø19.05mm (1)

Tube

Vinyl Tapes (2)

AQ

30/32

36

30/32

36

Insulation (1)

 

 

ENGLISH

 

 

 

150mm

 

 

 

 

 

 

 

 

 

 

 

Outdoor(Ø19.05mm) Indoor(Ø15.88mm)

 

 

 

Rubber Legs (4)

Pipe Clamps A (3)

Pipe Clamps B (3)

Cement Nails (6)

M4 x 25 Tapped

Drain Hose,

Putty 100g (1)

Screws (6)

length 2m (1)

 

 

 

 

 

Foam

 

 

 

 

 

 

Insulation(1)

 

 

 

 

 

 

• If these accessories are supplied, they will be in the accessory box.

Tools required for installation

General Tools

• Vacuum Pump(Backward flowing prevention)

• Manifold Gauge

• Stud Finder

• Torque Wrench

• Pipe Cutter

• Reamer

• Pipe Bender

• Spirit Level

• Screw Driver

• Spanner

• Drill

• L Wrench

• Measuring Tape

Tools for test operations

• Thermometer

• Resistance Meter • Electroscope

Fixing the installation plate

You can select the direction of the drain hose depending on where you want to install the indoor unit. Therefore before fixing the installation plate to a wall or a window frame, you must determine the position of the 65mm hole through which the cable, pipe and hose pass to connect the indoor unit to the outdoor unit.

When facing the wall, the pipe and cable can be connected from the:

• Right (A)

 

Direction of pipe

 

• Left (B)

 

 

 

• Underside_right (C)

A

 

B

• Rear_right or left (D)

 

 

D

D

C

1.Determine the position of the pipe and drain hose hole as seen in the picture and drill the hole with an inner diameter of 65mm so that it slants slightly downwards.

(Unit : mm)

 

67

156

364

 

 

34.5

19.5

64.5

•Make sure to drill only one hole after choosing the direction of the pipe.

29

MAX4 AQ&AST&U_IB&IM_DB98-34063A_E.indd 29

2013-3-18 15:46:38

Page 28 Page 30
Image 29
Page 28 Page 30
Contents English Contents Important safety symbols and precautions SafetAA y precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges ChecAA king before useChecAA king the name of the parts PowerMain parts  AQ/AS 30/32/36T  Display  AQ/AS 30/32/36TRemote controller buttons ChecAA king the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasicAA function Press the button to set the desired fan speed Press the button to adjust the temperaturePress the Air swing button on the remote controller Using the Turbo functionAdjusA ting the air flow direction Vertical air flowPress the button on the remote controller AA modePress the Time Up or Time Down button to set the time Press the Set button to active it onAdditional options available in On timer mode SettinAA g the On/Off timerPress the On Timer/Off Timer button From the moment you have set the timer Using the Smart Saver functionIf the air conditioner is on If the air conditioner is off Turn off automaticallyUsing the Quiet function UsingAA the Auto Clean functionWhen the air conditioner is turned on 30/32/36T 30/32/36UCleaning the outdoor unit heat exchanger Cleaning the indoor unitOpening the panel Heat exchangerCleaning the air filter CleanAA ing the air conditionerRemoving the Air filter Open the panel and put the Air filter outBio filter sky-blue AACleaning the air conditionerBio filter Deodorizing filter black Deodorizing filterPeriodical checks MainAA taining the air conditionerTroubleshootingAA Connection Flow movement changes. It is normalGeneral information Safety precautionsInstalling the unit Choosing the installation locationPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyOutdoor Unit ChooAA sing the installation locationWhere sulfide gas exists When the air outlet is towards the wall When installing more than 1 outdoor unit Figure Description Top view Side viewAccessories in the outdoor unit case AccessoriesAccessories in the indoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsConnecting the cable Connecting the assembly cableCable specification Installation Extend the assembly cable if necessaryEach wire is labeled with the corresponding terminal number Cut off the remaining foam insulation Smooth the cut edgesCutting or extending the pipe AAPurging the indoor unitUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flareOuter Diameter CuttingAA or extending the pipeTwo hoses are firmly connected, there is no water leakage Drain hose installationHose tight Check for leakage on both side of the drain outletAQseries Purging the connected pipesAdd refrigerant charge according to table below Adding RefrigerantIf you use a pipe shorter than 4 30/32 or 5 36 m Purge time is normalFixing the indoor unit in place PerfoAA rming the gas leak testsFixing the outdoor unit in place Outdoor unit installed on the wall by rackAppropriate support wall or ground ModelPress the Power button to stop the operation Press the Power button and check the followingFinalAA Check and Trial Operation Check the followingsInsulation tape to finish Apply heat to the contraction tube to contract itAfter tube contraction work is completed, wrap it with AS36UGBUMG AS30UGBUMG AATechnical SpecificationsEnglish Egypt Questions or COMMENTS?Air Conditioner
Top Page Image Contents