Samsung AS24VBFNUMG manual AA mode, Press the button on the remote controller, Set Off timer

Page 13

AA mode

For a comfortable sleep, the air conditioner will operate it Fall asleep Sound sleep Wake up from mode.

When the air conditioner is on and in cool/heat mode (Model AQ)

1. Press the button on the remote controller.

 indicator appears and Off timer indicator starts blinking on the remote controller display.

2. Press the button to set the time.

You can set the time in half hourly unit from 30 minutes ~ 3 hours and hour unit from

3 hours ~ 12 hours.

 Operating hour can be set from minimum 30 minutes to maximum 12 hours.

 Default operation hour is set to 8 hours.

ENGLISH

3. Press the Set/Cancel button to active it on.

 Off timer indicator stops blinking and reserved time will be displayed for 3 seconds. Then the air conditioner operates in good’sleep(Cool) mode.

 If you don’t press Set/Cancel button within 10 seconds after pressing the

button, the air conditioner will return to previous status. Check Off timer indicator and indicator on the indoor unit.

Cancel Press the Set/Cancel button once again.

You can set the desired temperature by 1˚C in the range of 16˚C~30˚C.

Fan speed will be adjusted automatically according to the mode.

However, I f you selectmode while heating operation is on, you can adjust fan speed. (Model AQ)

Air flow direction will be adjusted automatically according to the mode.

However, if you select mode while heating operation is on, you can adjust air flow direction. (Model AQ)

Temperature and fan speed changes in mode

•Fall asleep: Eases you into sleep by dropping the temperature.

•Sound sleep: Relaxes your body and raises your temperature slightly.

•Wake up from mode: Allows you to wake up from comfortable intermittent air and it makes you feel refreshed.

• Set Off timer in	mode over 5 hours. You fell disturbed sleep if the	is set too short or long
because the default is set to 8-hour-operation.

•If the mode is set less than 4 hours, the operation will stop at the same time.

If the mode is set over 5 hours, it will run as Wake up stage from the last one hour before it stops.

•Recommended set temperature is between 25˚C~27˚C for cooling.

13

UMG_AQ&AS18V@_IBIM_34038A_E--P14�P18��.indd 13

2013-3-18 11:00:09

Image 13

Contents English Contents Important safety symbols and precautions SafetAA y precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges ChecAA king before useSet temperature Mode indicator Auto clean indicatorMode indicator Room temperature ChecAA king the name of the partsRemote controller buttons ChecAA king the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasicAA function Press the button to set the desired fan speed Press the button to adjust the temperaturePress the Air swing button on the remote controller Using the Turbo functionAdjusA ting the air flow direction Vertical air flowPress the button on the remote controller AA modePress the Set/Cancel button to active it on Set Off timerPress the On Timer/Off Timer button SettinAA g the On/Off timerPress the On Timer/Off Timer button to set the time If the air conditioner is on If the air conditioner is off From the moment you have set the timerTurn off automatically Using the dlight Cool function Using the Smart Saver functionUsing the Virus Doctor function Using the Quiet function UsingAA the Auto Clean functionWhen the air conditioner is turned on RunsCleaning the outdoor unit heat exchanger Cleaning the indoor unitOpening the panel Heat exchangerRemoving the Air filter Cleaning the air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated areaClose the front panel Deodorizing and Bio filterPeriodical checks MainAA taining the air conditionerTroubAA leshooting Flow movement changes. It is normal TroubleshootingConnection General information Safety precautionsInstalling the unit Choosing the installation locationPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyOutdoor Unit Where sulfide gas existsModel When installing more than 1 outdoor unit ChoosingAA the installation locationWhen the air outlet is towards the wall  Figure DescriptionAccessories in the indoor unit case AccessoriesAccessories in the outdoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsCable specification Connecting the assembly cableConnecting the cable Each wire is labeled with the corresponding terminal number Extend the assembly cable if necessaryCut off the remaining foam insulation Smooth the cut edgesCutting or extending the pipe PurgiAA ng the indoor unitUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flareOuter Diameter Drain hose installationChanging direction of the drain hose AQseries Purging the connected pipesConnect a drain hose to the drain plug Ensure that condensation draining is adequateAdding Refrigerant Gas service port as seen in the pictureIf you use a pipe shorter than 4 or 5m Fixing the indoor unit in place PerfoAA rming the gas leak testsFixinAA g the outdoor unit in place Outdoor unit installed on the wall by rackPress the Power button to stop the operation Press the Mode button to select Cool modeCheck the followings Press the Air swing button and check the followingApply heat to the contraction tube to contract it AAHow to connect your extended power cablesAfter tube contraction work is completed, wrap it with Insulation tape to finishAQ18VBFUMG AQ24VBFUMG TechnAA ical SpecificationsQuestions or COMMENTS? Air Conditioner