Samsung AS24VBFNUMG, AS18VBFNUMG Check the followings, Press the Mode button to select Cool mode

Page 41

FinalAA Check and Trial Operation

To complete the installation, perform the following checks and tests to ensure that the air conditioner operates correctly.

Check the followings:

Strength of the installation site

Tightness of pipe connection to detect gas leak

Electric wiring connection

Heat-resistant insulation of the pipe

Drainage

Grounding conductor connection

Correct operation (follow the steps below)

1.Press the Power button and check the following:

The indicator on the indoor unit lights up.

The airflow blade opens and the fan gears up for operation.

ENGLISH

2.Press the Mode button to select Cool mode.

In Cool mode, use Temp + or - button and set the temperature at 16°C.

• Approximately 3~5 minutes later, outdoor unit will start to operate and the Cool air will blow out.

• After 12 minutes of stationary condition check the indoor unit air treatment:

Cooling mode (indoor unit check) Inlet air temp. - Outlet air temp : From 10°K to 12°K ( indicative delta T)

3. Press the Air swing button and check the following:

The airflow blades work properly.

4.Press the Power button to stop the operation.

• When you complete the installation successfully, hand over this manual to the user for storage in a handy and safe

place.

Pump down procedure (when removing the product)

1.Turn on the air conditioner and select Cool mode to run the compressor for 3 minutes.

2. Release the valve caps on High and Low pressure side.

3. Use L wrench to close the valve on the high pressure side.

4. Approximately 2 minutes after, close the valve on the low pressure side.

5. Stop operation of the air conditioner.

6. Disconnect the pipes.

41

UMG_AQ&AS18V@_IBIM_34038A_E--P14P18���������.indd 41

2013-3-18 11:00:20

Image 41
Contents English Contents Important safety symbols and precautions SafetAA y precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges ChecAA king before useSet temperature Mode indicator Auto clean indicatorMode indicator Room temperature ChecAA king the name of the partsRemote controller buttons ChecAA king the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasicAA function Press the button to set the desired fan speed Press the button to adjust the temperaturePress the Air swing button on the remote controller Using the Turbo functionAdjusA ting the air flow direction Vertical air flowPress the button on the remote controller AA modePress the Set/Cancel button to active it on Set Off timerPress the On Timer/Off Timer button to set the time SettinAA g the On/Off timerPress the On Timer/Off Timer button Turn off automatically From the moment you have set the timerIf the air conditioner is on If the air conditioner is off Using the dlight Cool function Using the Smart Saver functionUsing the Virus Doctor function Using the Quiet function UsingAA the Auto Clean functionWhen the air conditioner is turned on RunsCleaning the outdoor unit heat exchanger Cleaning the indoor unitOpening the panel Heat exchangerRemoving the Air filter Cleaning the air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated areaClose the front panel Deodorizing and Bio filterPeriodical checks MainAA taining the air conditionerTroubAA leshooting Connection TroubleshootingFlow movement changes. It is normal General information Safety precautionsInstalling the unit Choosing the installation locationPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyModel Where sulfide gas existsOutdoor Unit When installing more than 1 outdoor unit ChoosingAA the installation locationWhen the air outlet is towards the wall  Figure DescriptionAccessories in the outdoor unit case AccessoriesAccessories in the indoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsConnecting the cable Connecting the assembly cableCable specification Each wire is labeled with the corresponding terminal number Extend the assembly cable if necessaryCut off the remaining foam insulation Smooth the cut edgesCutting or extending the pipe PurgiAA ng the indoor unitUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flareOuter Diameter Drain hose installationChanging direction of the drain hose AQseries Purging the connected pipesConnect a drain hose to the drain plug Ensure that condensation draining is adequateIf you use a pipe shorter than 4 or 5m Gas service port as seen in the pictureAdding Refrigerant Fixing the indoor unit in place PerfoAA rming the gas leak testsFixinAA g the outdoor unit in place Outdoor unit installed on the wall by rackPress the Power button to stop the operation Press the Mode button to select Cool modeCheck the followings Press the Air swing button and check the followingApply heat to the contraction tube to contract it AAHow to connect your extended power cablesAfter tube contraction work is completed, wrap it with Insulation tape to finishAQ18VBFUMG AQ24VBFUMG TechnAA ical SpecificationsQuestions or COMMENTS? Air Conditioner