Samsung AS24VBFNUMG Accessories in the indoor unit case, Accessories in the outdoor unit case

Page 29

When the walls are blocking front and the rear side of the outdoor units

 

 

300 or more

600 or more

600 or more

1500 or more

When front and rear side of the outdoor unit is towards the wall

1500 or

600 or

3000 or

3000 or

200 or

more

more

more

more

more

(Unit : mm)

When the upper part of the outdoor unit and the air outlet is opposite the wall

500or more

ENGLISH

 

300 or more

500 or more

300 or more

 

• If installation is done in inappropriate space, unit may generate sound and cause bad effect on the product.

• Installation must be done in level and in a place where vibration will not cause any effect.

Accessories

The following accessories are supplied with the air conditioner:

• The number of each accessory is indicated in parentheses.

Accessories in the indoor unit case

Installation Plate

Remote

Batteries for

User’s & Installation

Remote Control

M4 x 16 Tapped

(1)

controller (1)

Remote controller (2)

Manual (1)

Holder (1)

Screws (2)

Accessories in the outdoor unit case

 

5-wire

 

3-wire

 

6-wire

Assembly Cable (1)

Assembly Cable (1)

Assembly Cable (1)

AQ09/12/18

AS09/12/18

 

AQ24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4-wire

Assembly Cable (1)

AS24

Tapón de drenado

(1)

AQ

Pata de hule (4)

• The flare nuts are attached to the end of each pipe of an evaporator or a service port.

Use the nuts when connecting the pipes.

The assembly cable is optional. If it is not supplied, use the standard cable.

The drain plug and rubber leg are only included when the air conditioner is supplied without the assembly pipe as seen in the picture below.

29

UMG_AQ&AS18V@_IBIM_34038A_E--P14P18���������.indd 29

2013-3-18 11:00:15

Image 29
Contents English Contents Important safety symbols and precautions SafetAA y precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges ChecAA king before useSet temperature Mode indicator Auto clean indicatorMode indicator Room temperature ChecAA king the name of the partsRemote controller buttons ChecAA king the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasicAA function Press the button to set the desired fan speed Press the button to adjust the temperaturePress the Air swing button on the remote controller Using the Turbo functionAdjusA ting the air flow direction Vertical air flowPress the button on the remote controller AA modePress the Set/Cancel button to active it on Set Off timerPress the On Timer/Off Timer button to set the time SettinAA g the On/Off timerPress the On Timer/Off Timer button Turn off automatically From the moment you have set the timerIf the air conditioner is on If the air conditioner is off Using the dlight Cool function Using the Smart Saver functionUsing the Virus Doctor function Using the Quiet function UsingAA the Auto Clean functionWhen the air conditioner is turned on RunsCleaning the outdoor unit heat exchanger Cleaning the indoor unitOpening the panel Heat exchangerRemoving the Air filter Cleaning the air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated areaClose the front panel Deodorizing and Bio filterPeriodical checks MainAA taining the air conditionerTroubAA leshooting Connection TroubleshootingFlow movement changes. It is normal General information Safety precautionsInstalling the unit Choosing the installation locationPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyModel Where sulfide gas existsOutdoor Unit When installing more than 1 outdoor unit ChoosingAA the installation locationWhen the air outlet is towards the wall  Figure DescriptionAccessories in the outdoor unit case AccessoriesAccessories in the indoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsConnecting the cable Connecting the assembly cableCable specification Each wire is labeled with the corresponding terminal number Extend the assembly cable if necessaryCut off the remaining foam insulation Smooth the cut edgesCutting or extending the pipe PurgiAA ng the indoor unitUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flareOuter Diameter Drain hose installationChanging direction of the drain hose AQseries Purging the connected pipesConnect a drain hose to the drain plug Ensure that condensation draining is adequateIf you use a pipe shorter than 4 or 5m Gas service port as seen in the pictureAdding Refrigerant Fixing the indoor unit in place PerfoAA rming the gas leak testsFixinAA g the outdoor unit in place Outdoor unit installed on the wall by rackPress the Power button to stop the operation Press the Mode button to select Cool modeCheck the followings Press the Air swing button and check the followingApply heat to the contraction tube to contract it AAHow to connect your extended power cablesAfter tube contraction work is completed, wrap it with Insulation tape to finishAQ18VBFUMG AQ24VBFUMG TechnAA ical SpecificationsQuestions or COMMENTS? Air Conditioner