Samsung AS24VBFNUMG manual PerfoAA rming the gas leak tests, Fixing the indoor unit in place

Page 39

PerfoAA rming the gas leak tests

Make sure to check for gas leaks before completing the installation process (connecting the assembly pipe and hose between indoor unit and outdoor unit, insulating the cables, hose and pipe, and fixing the indoor unit to the installation plate).

A C D

B

To check for gas leaks on the outdoor unit,

Check the valve A and B using a leak detector.

To check for gas leaks on the indoor unit,

Check the flare nut C and D using a leak detector.

ENGLISH

Fixing the indoor unit in place

Perform the following work on the area where gas leak test was done priorly.

 

 

After checking for gas leaks in the system, insulate the pipe, hose and cables.

Insulation

 

Then place the indoor unit on the installation plate.

 

 

1.

To avoid condensation problems, wrap foam insulation (as shown in the figure) on

 

 

a part without insulation on the end of the pipes.

 

 

2.

Wind the pipe, assembly cable and drain hose with vinyl tape.

Pipes

 

3.

Place the bundle (the pipe, assembly cable and drain hose) in the lower part

 

 

 

of the indoor unit carefully so it does not project from the rear of the indoor

Installation

 

 

unit.

 

4.

Hook the indoor unit to the installation plate and move the unit to the right

plate

Connecting

Vinyl tape

pipes

 

and left until it is securely in place.

 

Connecting wires

 

 

 

 

 

• Make sure pipe does not move when you install the indoor unit on

Drain hose

 

 

an installation plate.

 

 

5.Wrap the rest of the pipe with vinyl tape.

6.Attach the pipe to the wall using clamps (optional).

39

UMG_AQ&AS18V@_IBIM_34038A_E--P14P18���������.indd 39

2013-3-18 11:00:20

Image 39
Contents English Contents Wall socket SafetAA y precautionsImportant safety symbols and precautions Follow directionsFor Using For Cleaning Operation ranges ChecAA king before useChecAA king the name of the parts Mode indicator Auto clean indicatorSet temperature Mode indicator Room temperatureRemote controller buttons ChecAA king the remote controllerInserting the batteries Remote controller displayBattery changing time Storing the remote controllerBasicAA function Press the button to set the desired fan speed Press the button to adjust the temperatureVertical air flow Using the Turbo functionPress the Air swing button on the remote controller AdjusA ting the air flow directionSet Off timer AA modePress the button on the remote controller Press the Set/Cancel button to active it onSettinAA g the On/Off timer Press the On Timer/Off Timer buttonPress the On Timer/Off Timer button to set the time From the moment you have set the timer If the air conditioner is on If the air conditioner is offTurn off automatically Using the dlight Cool function Using the Smart Saver functionUsing the Virus Doctor function Runs UsingAA the Auto Clean functionUsing the Quiet function When the air conditioner is turned onHeat exchanger Cleaning the indoor unitCleaning the outdoor unit heat exchanger Opening the panelDry the Air filter in a ventilated area Cleaning the air filterRemoving the Air filter Open the panel and put the Air filter outClose the front panel Deodorizing and Bio filterPeriodical checks MainAA taining the air conditionerTroubAA leshooting Troubleshooting Flow movement changes. It is normalConnection General information Safety precautions a place where the air filter can be replaced easily Choosing the installation locationInstalling the unit Power supply line, fuse or circuit breakerWhere sulfide gas exists Outdoor UnitModel  Figure Description ChoosingAA the installation locationWhen installing more than 1 outdoor unit When the air outlet is towards the wallAccessories Accessories in the indoor unit caseAccessories in the outdoor unit case Tools for test operations Fixing the installation plateOptional accessories Tools required for installation General ToolsConnecting the assembly cable Cable specificationConnecting the cable Each wire is labeled with the corresponding terminal number Extend the assembly cable if necessaryCut off the remaining foam insulation Smooth the cut edgesPut a flare nut slightly into the pipe and modify the flare PurgiAA ng the indoor unitCutting or extending the pipe Unscrew the caps at the end of each pipeOuter Diameter Drain hose installationChanging direction of the drain hose Ensure that condensation draining is adequate Purging the connected pipesAQseries Connect a drain hose to the drain plugGas service port as seen in the picture Adding RefrigerantIf you use a pipe shorter than 4 or 5m Fixing the indoor unit in place PerfoAA rming the gas leak testsFixinAA g the outdoor unit in place Outdoor unit installed on the wall by rackPress the Air swing button and check the following Press the Mode button to select Cool modePress the Power button to stop the operation Check the followingsInsulation tape to finish AAHow to connect your extended power cablesApply heat to the contraction tube to contract it After tube contraction work is completed, wrap it withAQ18VBFUMG AQ24VBFUMG TechnAA ical SpecificationsQuestions or COMMENTS? Air Conditioner