Quadra-Fire VOYAGEUR-MBK, VOYAGEUR-PMH owner manual Blower Operating Instructions

Page 15

R

VOYAGEUR Wood Insert

N.Blower Control Box & Snap Disc Operating Instructions

1.The blower will turn on/off automatically when set to AUTO. Figure 15.1.

2.When set to MANUAL, the fan will turn on/off only when you turn it on or off. This setting over-rides the internal snap disc.

3.Swing the grille downward to expose the blower con- trols. Adjust the speed of the fan by turning the HIGH/ LOW knob to the desired setting.

O.Blower Operating Instructions

1.Initial (cold) startup: Open both controls fully by rais- ing the Burn Rate Air Control all the way up until it stops and PUSH the Start-up Air Control back until it stops. The blower tends to cool the appliance. Leave the blower off until the burn is well established, i.e., 30 minutes.

MANUAL: over- rides the internal snap disc

Blower Controls Under Ash Lip

AUTO: Fan with turn ON/OFF automatically and is controlled by the internal Snap Disc

2. High Burn Setting: Both controls are open. Burn Rate

Figure 15.1

 

Air Control is pulled up and the Start-up Air Control is

 

fully pushed in. Blower may remain on.

 

3.Medium-High Burn Setting*: Burn Rate Air Control is closed then opened to 1 inch to fully open (pull up). Blower may remain on.

4.Medium-Low Burn Setting*: Burn Rate Air Control is closed then opened to 1/4 inch to 1/2 inch (pull up). Leave the blower off until the burn is well established, i.e., 30 minutes.

5.Low Burn Setting*: Burn Rate Air Control is closed (down position). Leave the blower off until the burn is well established, i.e., 30 minutes.

*NOTE: For burn settings 3 to 5 the Start-up Air Control needs to be pushed in (Open) then pulled forward to activate the Automatic Combustion Control (ACC).

NOTE: For maximum effi ciency and lowest emissions, when operating the blower in either the automatic or manual setting for the low and medium low burn settings leave the blower off until the burn is well established, i.e., 30 minutes.

6.The blower is equipped with a rheostat (speed control). The highest blower speed is obtained by turning the rheostat on, then adjusting back towards “OFF” as far as possible without turning the blower off. For a low blower speed, turn the control knob clockwise as far as possible

NOTICE!

Do NOT operate a circulating fan within close proxim- ity, approximately 4 ft (1.2m), of appliance

•Can reverse air fl ow, blowing hot air into appliance cavity.

•Can damage appliance blower due to overheating.

November 22, 2011

7063-173D

Page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Hot glass will cause burns Voyageur Wood InsertMfg Date Voyageur Wood InsertSerial Number Model NameTable of Contents Voyageur Wood Insert Warranty Policy Voyageur Wood Insert Mobile Home Approved Listing and Code ApprovalsAppliance Certifi cation BTU & Effi ciency Specifi cationsYour Wood Appliance Operating InstructionsSeasoned Wood Voyageur Wood Insert Fire SafetyOverfi ring Combustible/Non-combustible MaterialsVoyageur Wood Insert Burning Process Second StageFinal Stage Kindling or First Stage Start-Up Air Control Manual Timer Over-RideVoyageur Wood Insert Automatic Combustion Control ACC Air ControlsVoyageur Wood Insert Burn Rates and Operating Effi ciency Correct Baffl e and Blanket Positions Voyageur Wood Insert Correct Baffl e & Blanket PlacementFuel Reloading Instructions Voyageur Wood Insert Building a FireHardwood vs Softwood Moisture Voyageur Wood Insert Wood FuelBlower Operating Instructions Frequently Asked Questions Voyageur Wood Insert Clear SpaceOpacity Smoke Your specifi c model Voyageur Wood Insert Quick Start GuideDisposal of Ashes Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Cleaning Plated SurfacesInspect Firebrick & Replacement Instructions Voyageur Wood Insert Glass CleaningMonthly Voyageur Wood Insert Quick Reference Maintenance GuideStart Fire Problems Possible Cause Solution Troubleshooting GuideWiring Diagram Service Parts ReplacementGlass Replacement Snap Disc Replacement ContdShock Risk Voyageur Wood Insert Blower ReplacementDoor Cross Voyageur Wood Insert Tube Channel Assembly Replacement Design and Installation Considerations Getting StartedDraft Voyageur Wood Insert Negative Pressure Chimney Termination Requirements Voyageur Wood Insert Locating Your Stove & ChimneyVoyageur Wood Insert Rule Voyageur Wood Insert Tools And Supplies Needed Inspect Appliance and ComponentsPre-Burn Check List Appliance Dimensions Dimensions and ClearancesMaximum Mantel Depth 12 inch 305mm Ember Protection Only Thermal Protection RequiredVoyageur Wood Insert Calculating Alternate Floor Protection Larger Chimneys Chimney SystemsVenting Systems InspectionsVoyageur Wood Insert Masonry Chimney Cont’d Voyageur Wood Insert Metal Heat Circulating Masonry Prefabricated Metal ChimneyReplaces without a permit will void the listing Voyageur Wood Insert Securing Chimney Components Altering the FireplaceFactory-Built Sold Fuel Fireplace Chimney Height / Rise and Run Voyageur Wood Insert Ovalizing Round Stainless Steel LinersAppliance Set-up Outside Air Kit InstallationFlue Adapter Leveling LegsVoyageur Wood Insert Securing Appliance to Stove Pipe/Liner Standard Surround & Trim Kit InstallationVoyageur Wood Insert Standard Surround & Cast Trim Kit Voyageur Wood Insert All Cast Surround Kit Blower Cord Installation on Left SidePlacement Slot Blower Access Assembly White Wire Mobile Home Installation Cast Iron Wood Insert Voyageur#7 Baffl e Protection Channel RService Parts#10 Brick Assembly At Depot#14 Access Assembly Stocked at Depot #13 Door AssemblyService Parts Stocked#18 Control Asembly This manual may be ordered from an authorized dealer Surrounds see diagrams on following27.6 #27 Surround AssembliesDate of Service Performed By Description of Service Voyageur Wood Insert Service And Maintenance LogVoyageur Wood Insert Service And Maintenance Log Cont’d Contact Information
Top Page Image Contents