Quadra-Fire VOYAGEUR-MBK owner manual Voyageur Wood Insert Ovalizing Round Stainless Steel Liners

Page 39

R

VOYAGEUR Wood Insert

J. Ovalizing Round Stainless Steel Liners

Ovalizing round stainless steel liners to accommodate the liner passing through the damper region of a ﬁ replace is an allowable and acceptable practice.

Ensure that the ovalization is minimized to the extent required to ﬁ t through the damper.

K. Chimney Height / Rise and Run

To be sure that your Quadra-Fire insert burns properly, the chimney draft (static pressure) should be approximately -0.10 inches water column (W.C.) during a high burn and -0.04 inches W.C. during a low burn, measured 6 inches (152mm) above the top of the insert after one hour of operation at each burn setting.

NOTE: These are guidelines only, and may vary somewhat for individual installations.

•This product was designed for and tested on a 6 inch (152mm) chimney, 14 to 16 feet (4.27-4.87m) high, (in- cludes appliance height) measured from the base of the appliance.

•The further your stack height or diameter varies from this conﬁ guration, the possibility of performance problems ex- ists.

•Chimney height may need to be increased by 2 - 3% per each 1000 feet (304.8m) above sea level.

•It is not recommended to use offsets or elbows at altitudes above 4000 feet (1219.2m) above sea level or when there are other factors that affect ﬂ ue draft.

WARNING

Fire Risk.

Do NOT pack insulation or other combustibles between spacers.

•ALWAYS maintain speciﬁ ed clearances around venting and spacers.

•Install spacers as speciﬁ ed.

Failure to keep insulation or other material away from vent pipe may cause ﬁ re.

WARNING

Fire Risk.

Failure to install a full reline may cause:

•Creosote accumulation creating increased risk of chimney ﬁ re.

•Lose protection to combustible surfaces from the liner in case of ﬁ re.

•Poor performance and start-ups.

•Less access to chimney for required maintenance.

WARNING

Fire Risk.

This appliance relies upon natural draft to operate properly.

•Chimney heights exceeding 25 feet (7.62m) from base of appliance may create an over-draft situation.

•Overdraft condition may create over-ﬁ ring.

Over-ﬁ ring may ignite creosote and/or damage appli- ance and chimney.

November 22, 2011

7063-173D

Page 39

Image 39

Contents Hot glass will cause burns Voyageur Wood InsertMfg Date Voyageur Wood InsertSerial Number Model NameTable of Contents Voyageur Wood Insert Warranty Policy Voyageur Wood Insert Mobile Home Approved Listing and Code ApprovalsAppliance Certiﬁ cation BTU & Efﬁ ciency Speciﬁ cationsYour Wood Appliance Operating InstructionsSeasoned Wood Voyageur Wood Insert Fire SafetyOverﬁ ring Combustible/Non-combustible MaterialsVoyageur Wood Insert Burning Process Second StageFinal Stage Kindling or First Stage Start-Up Air Control Manual Timer Over-RideVoyageur Wood Insert Automatic Combustion Control ACC Air ControlsVoyageur Wood Insert Burn Rates and Operating Efﬁ ciency Correct Bafﬂ e and Blanket Positions Voyageur Wood Insert Correct Bafﬂ e & Blanket PlacementFuel Reloading Instructions Voyageur Wood Insert Building a FireHardwood vs Softwood Moisture Voyageur Wood Insert Wood FuelBlower Operating Instructions Frequently Asked Questions Voyageur Wood Insert Clear SpaceOpacity Smoke Your speciﬁ c model Voyageur Wood Insert Quick Start GuideDisposal of Ashes Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Cleaning Plated SurfacesInspect Firebrick & Replacement Instructions Voyageur Wood Insert Glass CleaningMonthly Voyageur Wood Insert Quick Reference Maintenance GuideStart Fire Problems Possible Cause Solution Troubleshooting GuideWiring Diagram Service Parts ReplacementGlass Replacement Snap Disc Replacement ContdShock Risk Voyageur Wood Insert Blower ReplacementDoor Cross Voyageur Wood Insert Tube Channel Assembly Replacement Design and Installation Considerations Getting StartedDraft Voyageur Wood Insert Negative Pressure Chimney Termination Requirements Voyageur Wood Insert Locating Your Stove & ChimneyVoyageur Wood Insert Rule Voyageur Wood Insert Tools And Supplies Needed Inspect Appliance and ComponentsPre-Burn Check List Appliance Dimensions Dimensions and ClearancesMaximum Mantel Depth 12 inch 305mm Ember Protection Only Thermal Protection RequiredVoyageur Wood Insert Calculating Alternate Floor Protection Larger Chimneys Chimney SystemsVenting Systems InspectionsVoyageur Wood Insert Masonry Chimney Cont’d Voyageur Wood Insert Metal Heat Circulating Masonry Prefabricated Metal ChimneyReplaces without a permit will void the listing Voyageur Wood Insert Securing Chimney Components Altering the FireplaceFactory-Built Sold Fuel Fireplace Chimney Height / Rise and Run Voyageur Wood Insert Ovalizing Round Stainless Steel LinersAppliance Set-up Outside Air Kit InstallationFlue Adapter Leveling LegsVoyageur Wood Insert Securing Appliance to Stove Pipe/Liner Standard Surround & Trim Kit InstallationVoyageur Wood Insert Standard Surround & Cast Trim Kit Voyageur Wood Insert All Cast Surround Kit Blower Cord Installation on Left SidePlacement Slot Blower Access Assembly White Wire Mobile Home Installation Cast Iron Wood Insert Voyageur#7 Bafﬂ e Protection Channel RService Parts#10 Brick Assembly At Depot#14 Access Assembly Stocked at Depot #13 Door AssemblyService Parts Stocked#18 Control Asembly This manual may be ordered from an authorized dealer Surrounds see diagrams on following27.6 #27 Surround AssembliesDate of Service Performed By Description of Service Voyageur Wood Insert Service And Maintenance LogVoyageur Wood Insert Service And Maintenance Log Cont’d Contact Information