Quadra-Fire VOYAGEUR-MBK, VOYAGEUR-PMH Voyageur Wood Insert Burn Rates and Operating Efﬁ ciency

Page 11

R

VOYAGEUR Wood Insert

I. Burn Rates and Operating Efﬁ ciency

For maximum operating efﬁ ciency

1.Burn dry, well-seasoned wood.

2.Follow these burn rate instructions below and refer to

Figure 11.1.

*NOTE: These are guidelines. Actual settings may vary with type of wood, chimney draft, altitude and other variables.

Burn Rates

1. Starting a Fire and Reloading

•Open both controls fully by raising the Burn Rate Air Con- trol all the way up until it stops and push the Start-up Air Control back until it stops.

•The blower tends to cool the appliance. Leave the blower off until the burn is well established, i.e., 30 minutes.

•After loading the appliance with wood and starting the

ﬁre, set both controls to the desired setting by following the burn rate instructions below.

2. High Burn Rate - Maximum Heat*

•Raise the Burn Rate Air Control all the way up until it stops (top marker) to a fully open position.

•Push the Start-Up Air Control all the way back until it stops and leave it there.

•This setting over-rides the timer system (ACC) so you must monitor the ﬁ re closely while in this setting.

3. Medium-High Burn Rate - 15,000 to 30,000 BTU/hr*

HIGH

Burn Rate

Air Control

LOW

	To Activate Timer: Push back
	until it stops then pull forward until
Start-Up	it stops.
Air Control

Figure 11.1 Activating Timer

NOTE: If control is pushed all the way in it over-rides the timer (ACC).

•Raise the Burn Rate Air Control all the way up until it stops (top marker) to a fully open position.

•Push the Start-Up Air Control all the way back until it stops and then pull forward until it stops.

•This activates the timer system (ACC).

4. Medium-Low Burn Rate - 10,000 to 15,000 BTU/hr*

•Raise the Burn Rate Air Control up to the bottom of the middle marker and stop.

•Push the Start-Up Air Control until it stops.

•This activates the timer system (ACC).

5. Low Burn Rate - Below 10,000 BTU/hr*

•Leave the Burn Rate Air Control at the bottom marker.

•Push the Start-Up Air Control all the way back until it stops and then pull forward until it stops.

•This activates the timer system (ACC).

November 22, 2011

7063-173D

Page 11

Image 11

Contents Hot glass will cause burns Voyageur Wood InsertMfg Date Voyageur Wood InsertSerial Number Model NameTable of Contents Voyageur Wood Insert Warranty Policy Voyageur Wood Insert Mobile Home Approved Listing and Code ApprovalsAppliance Certiﬁ cation BTU & Efﬁ ciency Speciﬁ cationsYour Wood Appliance Operating InstructionsSeasoned Wood Voyageur Wood Insert Fire SafetyOverﬁ ring Combustible/Non-combustible MaterialsFinal Stage Kindling or First Stage Voyageur Wood Insert Burning ProcessSecond Stage Start-Up Air Control Manual Timer Over-RideVoyageur Wood Insert Automatic Combustion Control ACC Air ControlsVoyageur Wood Insert Burn Rates and Operating Efﬁ ciency Correct Bafﬂ e and Blanket Positions Voyageur Wood Insert Correct Bafﬂ e & Blanket PlacementFuel Reloading Instructions Voyageur Wood Insert Building a FireHardwood vs Softwood Moisture Voyageur Wood Insert Wood FuelBlower Operating Instructions Opacity Smoke Frequently Asked QuestionsVoyageur Wood Insert Clear Space Your speciﬁ c model Voyageur Wood Insert Quick Start GuideDisposal of Ashes Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Cleaning Plated SurfacesInspect Firebrick & Replacement Instructions Voyageur Wood Insert Glass CleaningMonthly Voyageur Wood Insert Quick Reference Maintenance GuideStart Fire Problems Possible Cause Solution Troubleshooting GuideWiring Diagram Service Parts ReplacementGlass Replacement Snap Disc Replacement ContdShock Risk Voyageur Wood Insert Blower ReplacementDoor Cross Voyageur Wood Insert Tube Channel Assembly Replacement Draft Design and Installation ConsiderationsGetting Started Voyageur Wood Insert Negative Pressure Chimney Termination Requirements Voyageur Wood Insert Locating Your Stove & ChimneyVoyageur Wood Insert Rule Pre-Burn Check List Voyageur Wood Insert Tools And Supplies NeededInspect Appliance and Components Appliance Dimensions Dimensions and ClearancesMaximum Mantel Depth 12 inch 305mm Ember Protection Only Thermal Protection RequiredVoyageur Wood Insert Calculating Alternate Floor Protection Larger Chimneys Chimney SystemsVenting Systems InspectionsVoyageur Wood Insert Masonry Chimney Cont’d Replaces without a permit will void the listing Voyageur Wood Insert Metal Heat Circulating MasonryPrefabricated Metal Chimney Factory-Built Sold Fuel Fireplace Voyageur Wood Insert Securing Chimney ComponentsAltering the Fireplace Chimney Height / Rise and Run Voyageur Wood Insert Ovalizing Round Stainless Steel LinersAppliance Set-up Outside Air Kit InstallationFlue Adapter Leveling LegsVoyageur Wood Insert Securing Appliance to Stove Pipe/Liner Standard Surround & Trim Kit InstallationVoyageur Wood Insert Standard Surround & Cast Trim Kit Voyageur Wood Insert All Cast Surround Kit Blower Cord Installation on Left SidePlacement Slot Blower Access Assembly White Wire Mobile Home Installation Cast Iron Wood Insert Voyageur#7 Bafﬂ e Protection Channel RService Parts#10 Brick Assembly At Depot#14 Access Assembly Stocked at Depot #13 Door Assembly#18 Control Asembly Service PartsStocked This manual may be ordered from an authorized dealer Surrounds see diagrams on following27.6 #27 Surround AssembliesDate of Service Performed By Description of Service Voyageur Wood Insert Service And Maintenance LogVoyageur Wood Insert Service And Maintenance Log Cont’d Contact Information