Quadra-Fire VOYAGEUR-MBK, VOYAGEUR-PMH Voyageur Wood Insert Metal Heat Circulating Masonry

Page 37

R

VOYAGEUR Wood Insert

E. Metal Heat Circulating Masonry

This insert conforms with the safety standard UL-1482 and ULC S628 (Canada) in all respects and is approved to UL & ULC safety standards for installation and use within a fi re- place with masonry chimney, in accordance with NFPA 211, and CAN/CSA-B365-01.

F. Prefabricated Metal Chimney

The chimney can be new or existing, masonry or prefabricated and must meet the following minimum requirements:

•Must be minimum 6 inch (152mm) inside diameter of high temperature chimney listed to UL 103 HT (2100oF) or ULC S628.

•Must use components required by the manufacturer for installation.

•Must maintain clearances required by the manufacturer for installation.

•Refer to manufacturers instructions for installation

•This insert is listed to UL 1482 Standard and is approved for installation into listed factory-built solid fuel fi replaces listed to UL 127 conforming to the follow- ing specifi cations and instructions:

•The original factory-built clearance fi replace chimney cap must be re-installed after installing the approved chimney liner meeting type UL 103 HT requirements (2100°F) per UL 1777.

•The liner must be securely attached to the insert fl ue collar and the chimney top.

•The air fl ow of the factory-built solid fuel fi replace system must not be altered. The fl ue liner top support attachment must not reduce the air fl ow for the existing air-cooled chimney system.

•No dilution air is allowed to enter the chimney.

1.Secure the fi replace damper in the open position. If this cannot be accomplished, it will be necessary to remove the damper.

2.Seal damper area of chimney around chimney connector with a high temperature sealant or seal insert against the face of the fi replace.

3.Both methods must be removable and replaceable for cleaning and re-installation.

 

Inches

Millimeters

 

 

 

Minimum Width of Cavity Opening - Front

32-7/8*

835

 

 

 

Minimum Width of Cavity Opening - Rear

19-1/8*

486

 

 

 

Minimum Height

21-1/2*

546

Minimum Depth from Front to Rear

18-1/8*

460

 

 

 

*You will need to add additional clearances to these dimensions for your specifi c installation. Also allow suf- fi cient clearance if you are installing an outside air kit.

NOTE: Refer to chimney liner manufacturer for recom- mendations on supporting the liner. Installation into

fireplaces without a permit will void the listing.

NOTICE: In Canada when using a factory-built chimney it must be safety listed, Type UL103 HT (2100oF) [1149oC] CLASS

“A” or conforming to CAN/ULC-S629M, STANDARD FOR 650oC FACTORY-BUILT CHIMNEYS.

WARNING

Fire Risk.

When lining air-cooled factory-built chimneys:.

•Run chimney liner approved to UL 1777 Type HT requirements (2100 degrees F)

•Re-install original factory built chimney cap

ONLY

•DO NOT block cooling air openings in chimney

•Blocking cooling air will overheat the chimney

To maintain the functionality of the fi replace’s chimney system you may use a Simpson Dura-Vent DuraLiner Slip Hanger, Part # 4671, and attach to the bottom of the

fireplace chimney cap to support the liner. You have two options to completing the installation.

Option one - Not required to use liner cap: Re-attach the existing top of the chimney cap.

Option two - Using liner cap:

Re-attach the existing top of the chimney cap and install a new storm collar and a new liner cap.

WARNING! Risk of Fire!

Follow venting manufacturer’s clearances and instructions when installing venting system.

November 22, 2011

7063-173D

Page 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Hot glass will cause burns Voyageur Wood InsertSerial Number Voyageur Wood InsertModel Name Mfg DateTable of Contents Voyageur Wood Insert Warranty Policy Voyageur Wood Insert Appliance Certifi cation Listing and Code ApprovalsBTU & Effi ciency Specifi cations Mobile Home ApprovedYour Wood Appliance Operating InstructionsOverfi ring Voyageur Wood Insert Fire SafetyCombustible/Non-combustible Materials Seasoned WoodSecond Stage Voyageur Wood Insert Burning ProcessFinal Stage Kindling or First Stage Voyageur Wood Insert Automatic Combustion Control ACC Manual Timer Over-RideAir Controls Start-Up Air ControlVoyageur Wood Insert Burn Rates and Operating Effi ciency Correct Baffl e and Blanket Positions Voyageur Wood Insert Correct Baffl e & Blanket PlacementFuel Reloading Instructions Voyageur Wood Insert Building a FireHardwood vs Softwood Moisture Voyageur Wood Insert Wood FuelBlower Operating Instructions Voyageur Wood Insert Clear Space Frequently Asked QuestionsOpacity Smoke Your specifi c model Voyageur Wood Insert Quick Start GuideChimney and Chimney Connector Inspection/Cleaning Maintenance and ServiceCleaning Plated Surfaces Disposal of AshesInspect Firebrick & Replacement Instructions Voyageur Wood Insert Glass CleaningMonthly Voyageur Wood Insert Quick Reference Maintenance GuideStart Fire Problems Possible Cause Solution Troubleshooting GuideGlass Replacement Service Parts ReplacementSnap Disc Replacement Contd Wiring DiagramShock Risk Voyageur Wood Insert Blower ReplacementDoor Cross Voyageur Wood Insert Tube Channel Assembly Replacement Getting Started Design and Installation ConsiderationsDraft Voyageur Wood Insert Negative Pressure Chimney Termination Requirements Voyageur Wood Insert Locating Your Stove & ChimneyVoyageur Wood Insert Rule Inspect Appliance and Components Voyageur Wood Insert Tools And Supplies NeededPre-Burn Check List Appliance Dimensions Dimensions and ClearancesMaximum Mantel Depth 12 inch 305mm Ember Protection Only Thermal Protection RequiredVoyageur Wood Insert Calculating Alternate Floor Protection Venting Systems Chimney SystemsInspections Larger ChimneysVoyageur Wood Insert Masonry Chimney Cont’d Prefabricated Metal Chimney Voyageur Wood Insert Metal Heat Circulating MasonryReplaces without a permit will void the listing Altering the Fireplace Voyageur Wood Insert Securing Chimney ComponentsFactory-Built Sold Fuel Fireplace Chimney Height / Rise and Run Voyageur Wood Insert Ovalizing Round Stainless Steel LinersAppliance Set-up Outside Air Kit InstallationFlue Adapter Leveling LegsVoyageur Wood Insert Securing Appliance to Stove Pipe/Liner Standard Surround & Trim Kit InstallationVoyageur Wood Insert Standard Surround & Cast Trim Kit Voyageur Wood Insert All Cast Surround Kit Blower Cord Installation on Left SidePlacement Slot Blower Access Assembly White Wire Mobile Home Installation Cast Iron Wood Insert Voyageur#10 Brick Assembly RService PartsAt Depot #7 Baffl e Protection Channel#14 Access Assembly Stocked at Depot #13 Door AssemblyStocked Service Parts#18 Control Asembly This manual may be ordered from an authorized dealer Surrounds see diagrams on following27.6 #27 Surround AssembliesDate of Service Performed By Description of Service Voyageur Wood Insert Service And Maintenance LogVoyageur Wood Insert Service And Maintenance Log Cont’d Contact Information
Top Page Image Contents