Quadra-Fire VOYAGEUR-PMH, VOYAGEUR-MBK owner manual Appliance Set-up, Outside Air Kit Installation

Page 40

R

VOYAGEUR Wood Insert

9Appliance Set-up

Remove the zip tie to the lower access cover. It is to prevent the cover opening during shipping.

A. Outside Air Kit Installation

A source of air (oxygen) is necessary in order for combustion to take place. Whatever combustion air is consumed by the fi re must be replaced. Air is replaced via air leakage around win- dows and under doors. In homes that have tightly sealed doors and windows, an outside air source is needed. An optional Out- side Air Kit is available.

WARNING

Fire Risk.

Asphyxiation Risk.

Do not draw outside combustion air from:

•Wall, fl oor or ceiling cavity

•Enclosed space such as an attic or garage

•Close proximity to exhaust vents or chimneys

Fumes or odor may result

Items Needed for Installation (not supplied)

•4 inch fl ex aluminum pipe, or if using alternate material,

then it shall be made from durable, non-combustible, heat resistant material up to 350oF. Cut the pipe to the required length for your installation.

•Phillips head screw driver

•Silicone sealant

WARNING

Asphyxiation Risk.

Outside air inlet must be located to prevent blockage from:

•Leaves, snow, ice or other debris Block may cause combustion air starvation

Smoke spillage may set off alarms or irritate sensitive indi- viduals.

If Not Installing the Outside Air Kit

1.Swing grille down to expose the two screws. Figure 40.1

2.Remove the two screws and pull the access assembly away from the appliance.

3.Remove the outside air cover plate A and discard.

4.Re-install the access assembly.

Option One - Outside Air Installation Instructions

1.Remove the outside air cover plate B on outer can and dis- card. Figure 40.2.

2.Install optional fl ex adapter to outer can with the same screws. Do not use plastic wire ties that come with the kit as they will melt. NOTE: You may need to install the fl ex pipe into the fi rebox fi rst depending on installation. Attach fl ex to adapater with at least 2 screws.

3.Ensure existing access hole in fi replace is suffi cient to feed the 4 inch fl ex.

4.After sliding can into fi replace, feed fl ex into cut opening to obtain outside combustion air.

5.Level outer can and install appliance. See page 41.

Option Two - Outside Air Installation Instructions

1.Remove the outside air cover plate B on outer can and dis- card and reuse the 4 screws.

2.Ensure existing acces hole in fi replace will not be covered by the outer can. Existing outside air intake hole may be under at the rear or side of outer can. Outside air may also enter down existing chimney chase in some situations.

3.Repeat step 5 under Option One with one exception. After installing the appliance in the outer can, seal the fi replace opening and trim package with insulation to prevent air leak- age into the room.

WARNING

Asphyxiation Risk.

Length of outside air supply duct shall NOT exceed the length of the vertical height of the exhaust fl ue.

•Fire will not burn properly

•Smoke spillage occurs when door is opened due to air starvation.

Grille hinges

 

downward

 

Remove Screws &

 

Pull Access Assembly

Remove Outside Cover

away from Insert

Plate A (DISCARD)

 

Figure 40.1

Outside Air Cover

Plate B (DISCARD)

Termination

Cap

Flex Adapter

Figure 40.2

Page 40

7063-173D

November 22, 2011

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Voyageur Wood Insert Hot glass will cause burnsVoyageur Wood Insert Serial NumberModel Name Mfg DateTable of Contents Voyageur Wood Insert Warranty Policy Voyageur Wood Insert Listing and Code Approvals Appliance Certifi cationBTU & Effi ciency Specifi cations Mobile Home ApprovedOperating Instructions Your Wood ApplianceVoyageur Wood Insert Fire Safety Overfi ringCombustible/Non-combustible Materials Seasoned WoodSecond Stage Voyageur Wood Insert Burning ProcessFinal Stage Kindling or First Stage Manual Timer Over-Ride Voyageur Wood Insert Automatic Combustion Control ACCAir Controls Start-Up Air ControlVoyageur Wood Insert Burn Rates and Operating Effi ciency Voyageur Wood Insert Correct Baffl e & Blanket Placement Correct Baffl e and Blanket PositionsVoyageur Wood Insert Building a Fire Fuel Reloading InstructionsVoyageur Wood Insert Wood Fuel Hardwood vs Softwood MoistureBlower Operating Instructions Voyageur Wood Insert Clear Space Frequently Asked QuestionsOpacity Smoke Voyageur Wood Insert Quick Start Guide Your specifi c modelMaintenance and Service Chimney and Chimney Connector Inspection/CleaningCleaning Plated Surfaces Disposal of AshesVoyageur Wood Insert Glass Cleaning Inspect Firebrick & Replacement InstructionsVoyageur Wood Insert Quick Reference Maintenance Guide MonthlyTroubleshooting Guide Start Fire Problems Possible Cause SolutionService Parts Replacement Glass ReplacementSnap Disc Replacement Contd Wiring DiagramVoyageur Wood Insert Blower Replacement Shock RiskDoor Cross Voyageur Wood Insert Tube Channel Assembly Replacement Getting Started Design and Installation ConsiderationsDraft Voyageur Wood Insert Negative Pressure Voyageur Wood Insert Locating Your Stove & Chimney Chimney Termination RequirementsVoyageur Wood Insert Rule Inspect Appliance and Components Voyageur Wood Insert Tools And Supplies NeededPre-Burn Check List Dimensions and Clearances Appliance DimensionsMaximum Mantel Depth 12 inch 305mm Thermal Protection Required Ember Protection OnlyVoyageur Wood Insert Calculating Alternate Floor Protection Chimney Systems Venting SystemsInspections Larger ChimneysVoyageur Wood Insert Masonry Chimney Cont’d Prefabricated Metal Chimney Voyageur Wood Insert Metal Heat Circulating MasonryReplaces without a permit will void the listing Altering the Fireplace Voyageur Wood Insert Securing Chimney ComponentsFactory-Built Sold Fuel Fireplace Voyageur Wood Insert Ovalizing Round Stainless Steel Liners Chimney Height / Rise and RunOutside Air Kit Installation Appliance Set-upLeveling Legs Flue AdapterStandard Surround & Trim Kit Installation Voyageur Wood Insert Securing Appliance to Stove Pipe/LinerVoyageur Wood Insert Standard Surround & Cast Trim Kit Blower Cord Installation on Left Side Voyageur Wood Insert All Cast Surround KitPlacement Slot Blower Access Assembly White Wire Mobile Home Installation Voyageur Cast Iron Wood InsertRService Parts #10 Brick AssemblyAt Depot #7 Baffl e Protection ChannelStocked at Depot #13 Door Assembly #14 Access AssemblyStocked Service Parts#18 Control Asembly Surrounds see diagrams on following This manual may be ordered from an authorized dealer#27 Surround Assemblies 27.6Voyageur Wood Insert Service And Maintenance Log Date of Service Performed By Description of ServiceVoyageur Wood Insert Service And Maintenance Log Cont’d Contact Information
Top Page Image Contents