Quadra-Fire VOYAGEUR-PMH, VOYAGEUR-MBK owner manual Voyageur Wood Insert All Cast Surround Kit

Page 44

R

VOYAGEUR Wood Insert

H. All Cast Surround Kit

Size: 40 in. W x 30 in. H

Included in Surround Kit: (2) side pieces, left and right; (1) l top piece; (1) fastener package.

Tools Needed: Powered 4 to 6 inches long Phillips head screw driver; pliers

1.Remove contents from box being careful not to scratch or damage the cast trim pieces.

2.Lay surround pieces face down on a protected surface to prevent scratching.

3.Align the bosses on the top piece to the holes on the side pieces. Secure the 3 pieces together.

4.Attach the mounting brackets to the side pieces included with the kit. Figure 44.1.

5.In order to get a tight seal for the surround, you must reposition a side shield. There are two holes on the shield and it will come from the factory secured in the ﬁ rst (left) hole. Remove the shield and re-install using the second (right) hole. Figure 44.2.

5.Position the trim on the appliance matching up the mounting brackets with the slots on the appliance.

6.Attach the surround to the appliance 2 screws.

DO NOT OVERTIGHTEN SCREWS - MAY DAMAGE PROCELAIN FINISH.

I. Blower Cord Installation on Left Side

The blower cord is shipped to be installed on the right side of the appliance. You may relocate the cord so it is on the left side.

Overview: You are removing the power cord from the blower controls, re-routing the cord to the left side and re- installing the power cord to the blower controls. Refer to the exploded drawing on page 45.

Figure 44.3

4 Mounting Brackets

Figure 44.1

Mounting
Brackets
Attach to Appliance	Remove and Reposition
Attach to Appliance
with Screws	Side Shield using Second
with Screws
Do not overtighten - may	Hole
Do not overtighten - may
damage porcelain finish

1.Swing the grille down to expose the 2 bolts, one at each end. Remove the bolts and pull blower access assembly away from appliance and store away from your work area.

Figure 44.4

2.Remove the 2 screws in the hold down bracket in front of the blower assembly. You do not need to remove the blower from the hold down bracket.

3.Disconnect the 2 blower wires that are attached to the wire harness and pull the blower assembly away from the appliance.

Figure 44.2

Page 44

7063-173D

November 22, 2011

Image 44

Contents Voyageur Wood Insert Hot glass will cause burnsVoyageur Wood Insert Serial NumberModel Name Mfg DateTable of Contents Voyageur Wood Insert Warranty Policy Voyageur Wood Insert Listing and Code Approvals Appliance Certiﬁ cationBTU & Efﬁ ciency Speciﬁ cations Mobile Home ApprovedOperating Instructions Your Wood ApplianceVoyageur Wood Insert Fire Safety Overﬁ ringCombustible/Non-combustible Materials Seasoned WoodFinal Stage Kindling or First Stage Voyageur Wood Insert Burning ProcessSecond Stage Manual Timer Over-Ride Voyageur Wood Insert Automatic Combustion Control ACCAir Controls Start-Up Air ControlVoyageur Wood Insert Burn Rates and Operating Efﬁ ciency Voyageur Wood Insert Correct Bafﬂ e & Blanket Placement Correct Bafﬂ e and Blanket PositionsVoyageur Wood Insert Building a Fire Fuel Reloading InstructionsVoyageur Wood Insert Wood Fuel Hardwood vs Softwood MoistureBlower Operating Instructions Opacity Smoke Frequently Asked QuestionsVoyageur Wood Insert Clear Space Voyageur Wood Insert Quick Start Guide Your speciﬁ c modelMaintenance and Service Chimney and Chimney Connector Inspection/CleaningCleaning Plated Surfaces Disposal of AshesVoyageur Wood Insert Glass Cleaning Inspect Firebrick & Replacement InstructionsVoyageur Wood Insert Quick Reference Maintenance Guide MonthlyTroubleshooting Guide Start Fire Problems Possible Cause SolutionService Parts Replacement Glass ReplacementSnap Disc Replacement Contd Wiring DiagramVoyageur Wood Insert Blower Replacement Shock RiskDoor Cross Voyageur Wood Insert Tube Channel Assembly Replacement Draft Design and Installation ConsiderationsGetting Started Voyageur Wood Insert Negative Pressure Voyageur Wood Insert Locating Your Stove & Chimney Chimney Termination RequirementsVoyageur Wood Insert Rule Pre-Burn Check List Voyageur Wood Insert Tools And Supplies NeededInspect Appliance and Components Dimensions and Clearances Appliance DimensionsMaximum Mantel Depth 12 inch 305mm Thermal Protection Required Ember Protection OnlyVoyageur Wood Insert Calculating Alternate Floor Protection Chimney Systems Venting SystemsInspections Larger ChimneysVoyageur Wood Insert Masonry Chimney Cont’d Replaces without a permit will void the listing Voyageur Wood Insert Metal Heat Circulating MasonryPrefabricated Metal Chimney Factory-Built Sold Fuel Fireplace Voyageur Wood Insert Securing Chimney ComponentsAltering the Fireplace Voyageur Wood Insert Ovalizing Round Stainless Steel Liners Chimney Height / Rise and RunOutside Air Kit Installation Appliance Set-upLeveling Legs Flue AdapterStandard Surround & Trim Kit Installation Voyageur Wood Insert Securing Appliance to Stove Pipe/LinerVoyageur Wood Insert Standard Surround & Cast Trim Kit Blower Cord Installation on Left Side Voyageur Wood Insert All Cast Surround KitPlacement Slot Blower Access Assembly White Wire Mobile Home Installation Voyageur Cast Iron Wood InsertRService Parts #10 Brick AssemblyAt Depot #7 Bafﬂ e Protection ChannelStocked at Depot #13 Door Assembly #14 Access Assembly#18 Control Asembly Service PartsStocked Surrounds see diagrams on following This manual may be ordered from an authorized dealer#27 Surround Assemblies 27.6Voyageur Wood Insert Service And Maintenance Log Date of Service Performed By Description of ServiceVoyageur Wood Insert Service And Maintenance Log Cont’d Contact Information