Quadra-Fire VOYAGEUR-MBK, VOYAGEUR-PMH owner manual Voyageur Wood Insert Glass Cleaning

Page 19

R

VOYAGEUR Wood Insert

E. Glass Cleaning

•Frequency: As desired

•By: Homeowner

•Clean glass with a non-abrasive glass cleaner. Abrasive cleaners may scratch and cause glass to crack.

•If the deposits on the glass are not very heavy, normal glass cleaners work well. Heavier deposits may be removed by using a damp cloth dipped in wood ashes or by using a commercially available oven cleaner.

•After using an oven cleaner, it is advisable to remove any residue with a glass cleaner or soap and water. Oven cleaner left on during the next fi ring can permanently stain the glass and damage the fi nish on plated metal surfaces.

•A portion of the combustion air entering the fi rebox is de- fl ected down over the inside of the door glass.

•This air fl ow “washes” the glass, helping to keep smoke from adhering to its surface.

•When operated at a low burn rate, less air will be fl owing over the glass and the smoky, relatively cool condition of a low fi re will cause the glass to become coated.

•Operating the appliance with the Burn Rate Air Control and Start-Up Air Control all the way open for 15-20 min- utes should remove the built up coating.

CAUTION! Handle glass assembly with care. Glass is

breakable.

•Avoid striking, scratching or slamming glass

•Avoid abrasive cleaners

•Do not clean glass while it is hot

F.Inspect Firebrick & Replacement Instructions

•Frequency: After each ash removal

•By: Homeowner

Replace the fi rebrick if they become crumbly and/or if there is a 1/4 inch (6.35mm) gap between the bricks.

The fi rebox is lined with fi rebrick, which has exceptional insulating properties. Do not use a grate; simply build a fi re on the fi rebox fl oor. Do not operate appliance without fi rebrick.

1.After the coals have completely cooled, remove all old brick and ash from unit and vacuum fi rebox.

2.Remove new brick set from box and lay out to the diagram shown in the instructions that come with the replacement brick set.

3.Lay bottom bricks in unit.

4.Install rear bricks on the top of the bottom bricks.

5.Install side bricks. Slide top of brick under clips on side of fi rebox and push the bottom of the brick until it is fl ush with the side of the unit.

Use Part 832-0550 when ordering individual brick. Provide brick dimension or copy the page in the service parts list, mark the desired brick and take it to your authorized dealer.

November 22, 2011

7063-173D

Page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Hot glass will cause burns Voyageur Wood InsertMfg Date Voyageur Wood InsertSerial Number Model NameTable of Contents Voyageur Wood Insert Warranty Policy Voyageur Wood Insert Mobile Home Approved Listing and Code ApprovalsAppliance Certifi cation BTU & Effi ciency Specifi cationsYour Wood Appliance Operating InstructionsSeasoned Wood Voyageur Wood Insert Fire SafetyOverfi ring Combustible/Non-combustible MaterialsSecond Stage Voyageur Wood Insert Burning ProcessFinal Stage Kindling or First Stage Start-Up Air Control Manual Timer Over-RideVoyageur Wood Insert Automatic Combustion Control ACC Air ControlsVoyageur Wood Insert Burn Rates and Operating Effi ciency Correct Baffl e and Blanket Positions Voyageur Wood Insert Correct Baffl e & Blanket PlacementFuel Reloading Instructions Voyageur Wood Insert Building a FireHardwood vs Softwood Moisture Voyageur Wood Insert Wood FuelBlower Operating Instructions Voyageur Wood Insert Clear Space Frequently Asked QuestionsOpacity Smoke Your specifi c model Voyageur Wood Insert Quick Start GuideDisposal of Ashes Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Cleaning Plated SurfacesInspect Firebrick & Replacement Instructions Voyageur Wood Insert Glass CleaningMonthly Voyageur Wood Insert Quick Reference Maintenance GuideStart Fire Problems Possible Cause Solution Troubleshooting GuideWiring Diagram Service Parts ReplacementGlass Replacement Snap Disc Replacement ContdShock Risk Voyageur Wood Insert Blower ReplacementDoor Cross Voyageur Wood Insert Tube Channel Assembly Replacement Getting Started Design and Installation ConsiderationsDraft Voyageur Wood Insert Negative Pressure Chimney Termination Requirements Voyageur Wood Insert Locating Your Stove & ChimneyVoyageur Wood Insert Rule Inspect Appliance and Components Voyageur Wood Insert Tools And Supplies NeededPre-Burn Check List Appliance Dimensions Dimensions and ClearancesMaximum Mantel Depth 12 inch 305mm Ember Protection Only Thermal Protection RequiredVoyageur Wood Insert Calculating Alternate Floor Protection Larger Chimneys Chimney SystemsVenting Systems InspectionsVoyageur Wood Insert Masonry Chimney Cont’d Prefabricated Metal Chimney Voyageur Wood Insert Metal Heat Circulating MasonryReplaces without a permit will void the listing Altering the Fireplace Voyageur Wood Insert Securing Chimney ComponentsFactory-Built Sold Fuel Fireplace Chimney Height / Rise and Run Voyageur Wood Insert Ovalizing Round Stainless Steel LinersAppliance Set-up Outside Air Kit InstallationFlue Adapter Leveling LegsVoyageur Wood Insert Securing Appliance to Stove Pipe/Liner Standard Surround & Trim Kit InstallationVoyageur Wood Insert Standard Surround & Cast Trim Kit Voyageur Wood Insert All Cast Surround Kit Blower Cord Installation on Left SidePlacement Slot Blower Access Assembly White Wire Mobile Home Installation Cast Iron Wood Insert Voyageur#7 Baffl e Protection Channel RService Parts#10 Brick Assembly At Depot#14 Access Assembly Stocked at Depot #13 Door AssemblyStocked Service Parts#18 Control Asembly This manual may be ordered from an authorized dealer Surrounds see diagrams on following27.6 #27 Surround AssembliesDate of Service Performed By Description of Service Voyageur Wood Insert Service And Maintenance LogVoyageur Wood Insert Service And Maintenance Log Cont’d Contact Information
Top Page Image Contents