Quadra-Fire 7046-137C warranty Burn Rates and Operating Efficiency

Page 11

R

2700-I ACC Wood Insert

3. Burn Rate Air Control

•The air supply enters at the upper front of the firebox, near the top of the glass door.

•This preheated air supplies the necessary fresh oxygen to mix with the unburned gases, helping to create the second, third and fourth combustion process.

•This air is regulated by the Burn Rate Air Control.

•There are four settings High, Medium-High, Medium-Low and Low.

•When the control is raised all the way up it is on the High setting and when pushed all the down it is on the Low setting. Figure 11.1.

I. Burn Rates and Operating Efficiency

For maximum operating efficiency

1.This appliance has a timer system (ACC) that operates the appliance at its maximum efficiency removing any guess work for the homeowner. Follow the instructions below for each burn rate for the Start-Up Air Control and Burn Rate Air Control. Figure 11.1.

2.Burn dry, well-seasoned wood.

Burn Rates

1. Starting a Fire and Reloading

•Open both controls fully by raising the Burn Rate Air Con- trol all the way up until it stops and push the Start-up Air Control back until it stops.

•The blower tends to cool the appliance. Leave the blower off until the burn is well established, i.e., 30 minutes.

•After loading the appliance with wood and starting the fire, set both controls to the desired setting by following the burn rate instructions below.

2. High Burn Rate - Maximum Heat*

•Raise the Burn Rate Air Control all the way up until it stops (top marker) to a fully open position.

•Push the Start-Up Air Control all the way back until it stops and leave it there.

•This setting over-rides the timer system (ACC) so you must monitor the fire closely while in this setting.

3. Medium-High Burn Rate - 15,000 to 30,000 BTU/hr*

•Raise the Burn Rate Air Control all the way up until it stops (top marker) to a fully open position.

•Push the Start-Up Air Control all the way back until it stops and then pull forward until it stops.

•This activates the timer system (ACC).

4. Medium-Low Burn Rate - 10,000 to 15,000 BTU/hr*

•Raise the Burn Rate Air Control up to the bottom of the middle marker and stop.

•Push the Start-Up Air Control until it stops.

•This activates the timer system (ACC).

5. Low Burn Rate - Below 10,000 BTU/hr*

•Leave the Burn Rate Air Control at the bottom marker.

•Push the Start-Up Air Control all the way back until it stops and then pull forward until it stops.

•This activates the timer system (ACC).

*NOTE: These are approximate settings, and will vary with type of wood or chimney draft. Due to altitude and other environmental circumstances, this operational information is a guideline only.

WARNING

Risk of Fire.

When set on High Burn Rate and over-riding the Automatic Combustion Control system an overfire situation can occur and may result in a chimney fire.

Overfiring will void the stove warranty.

HIGH

LOW

Low (Closed)

High (Opened)

Burn Rate

Air Control

Start-Up Air Control

IN / OUT

Figure 11.1 Activating Timer

NOTE: If control is set full inward on “HI” it over-rides the timer (ACC).

December 15, 2009

7046-137C

Page 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Hot glass will cause burns ACC Wood InsertSerial Number ACC Wood InsertTable of Contents ACC Wood Insert Warranty Policy ACC Wood Insert Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Listing and Code ApprovalsYour Wood Appliance Operating InstructionsSeasoned Wood ACC Wood Insert Fire SafetyCombustible/Non-combustible Materials OverfiringFinal Stage ACC Wood Insert Burning ProcessKindling or First Stage Second StageStart-Up Air Control Manual Timer Over-RideACC Wood Insert Automatic Combustion Control ACC Air ControlsBurn Rates and Operating Efficiency Incorrect Baffle and Blanket Positions Correct Baffle and Blanket PositionsACC Wood Insert Building a Fire Do not USE Chemicals or Fluids to Start a Fire ACC Wood Insert Wood FuelBlower Operating Instructions Opacity Smoke Frequently Asked QuestionsACC Wood Insert Clear Space Disposal of Ashes Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Cleaning Plated SurfacesInspect Firebrick ACC Wood Insert Glass CleaningInspect Firebrick Cont’d Baffle & Blanket Placement Start Fire Problems Possible Cause Solution Troubleshooting GuideGlass Replacement Snap Disc Replacement Service Parts ReplacementShock Risk ACC Wood Insert Blower ReplacementBaffle & Ceramic Blanket Removal ACC Wood Insert Door Handle AssemblyACC Wood Insert Tube Channel Assembly Replacement Draft Design and Installation ConsiderationsGetting Started ACC Wood Insert Negative Pressure Chimney Termination Requirements ACC Wood Insert Locating Your Stove & ChimneyFlat Roof ACC Wood Insert RulePre-Use Check List ACC Wood Insert Tools And Supplies NeededInspect Appliance and Components Appliance Dimensions Dimensions and ClearancesSideWall Required Build On-Site Hearth Support AccessoryACC Wood Insert Zero Clearance Floor Protection Full RelineACC Wood Insert Calculating Alternate Floor Protection Masonry Chimney Chimney SystemsVenting Systems InspectionsACC Wood Insert Masonry Chimney Cont’d 36.1 ACC Wood Insert Metal Heat Circulating MasonryPrefabricated Metal Chimney Altering the Fireplace ACC Wood Insert Prefabricated Metal Chimney Cont’dSecuring Chimney Components Chimney Height / Rise and Run ACC Wood Insert Zero-Clearance FireplaceOvalizing Round Stainless Steel Liners Option Two Installation Instructions Outside Air Kit InstallationItems Needed for Installation not supplied Option One Installation InstructionsFlue Adapter Leveling LegsSlide Top Installation Instructions ACC Wood Insert Surround & Trim Kit Installation Cont’dInstructions ACC Wood Insert Blower Cord Installation on Left SideShears, Measuring Tape, Gloves ACC Wood Insert Zero Clearance Adjustable Trim SupportAdjustable from 2 inches to 10 inches Mobile Home Installation Exploded Drawings Reference MaterialsFigure a Important this is Dated Information HOW to Order ACC Wood Insert Service Parts & AccessoriesStocked At Depot Description Comments Part Number Fasteners StockedDescription Comments Part Number Date of Service Performed By Description of Service ACC Wood Insert Service And Maintenance LogContact Information
Top Page Image Contents