Quadra-Fire 7046-137C ACC Wood Insert Metal Heat Circulating Masonry, Prefabricated Metal Chimney

Page 36

2700-I ACC Wood Insert

R

E. Metal Heat Circulating Masonry

This insert conforms with the safety standard UL-1482 and ULC S628 (Canada) in all respects and is approved to UL & ULC safety standards for installation and use within a fire- place with masonry chimney, in accordance with NFPA 211, with a direct flue collar connection.

•The original factory-built clearance fireplace chimney cap must be re-installed after installing the approved chimney liner meeting type UL 103 HT requirements (2100°F) per UL 1777.

•If the chimney is not listed as meeting HT requirements, or if the factory built fireplace was tested prior to 1998, a full height listed chimney liner must be installed from the appliance flue collar to the chimney top.

F. Prefabricated Metal Chimney

The chimney can be new or existing, masonry or prefabricated and must meet the following minimum requirements:

•Must be minimum 6 inch (152mm) inside diameter of high temperature chimney listed to UL 103 HT (2100oF) or ULC S628.

•Must use components required by the manufacturer for installation.

•Must maintain clearances required by the manufacturer for installation.

•Refer to manufacturers instructions for installation

•This insert is listed to UL 1482 Standard and is approved for installation into listed factory-built zero clearance fireplaces listed to UL 127 conforming to the following specifications and instructions:

•The liner must be securely attached to the insert flue collar and the chimney top.

•The air flow of the factory-built zero-clearance fireplace system must not be altered. The flue liner top support attachment must not reduce the air flow for the existing air-cooled chimney system.

•No dilution air is allowed to enter the chimney.

1.Secure the fireplace damper in the open position. If this cannot be accomplished, it will be necessary to remove the damper.

2.Seal damper area of chimney around chimney connector with a high temperature sealant or seal insert against the face of the fireplace.

3.Both methods must be removable and replaceable for cleaning and re-installation.

 

Flue Liner with Required Air Space

 

 

 

Stainless Steel Chimney Connector

 

 

 

Must Extend to Flue Liner

 

 

Minimum 8” (203mm) Masonry Thickness

 

 

 

in Front of Smoke Chamber

 

 

 

 

 

Airtight Insulated Clean-Out

Minimum Clearance in Accordance with

 

 

 

Insert Listing

 

Damper Plate Removed or

 

 

 

 

 

 

Fastened in Open Position

 

Floor Protection in

 

 

 

Accordance with Insert

 

Seal with Non-

 

Listing

 

 

 

Combustible Material

 

 

 

 

Combustible Floor

 

 

 

 

NOTE: Generic wood insert shown - not model specific

Figure

36.1

 

 

Page 36

7046-137C

December 15, 2009

Page 35 Page 37
Image 36
Page 35 Page 37
Contents ACC Wood Insert Hot glass will cause burnsACC Wood Insert Serial NumberTable of Contents ACC Wood Insert Warranty Policy ACC Wood Insert BTU & Efficiency Specifications Glass SpecificationsListing and Code Approvals Appliance CertificationOperating Instructions Your Wood ApplianceACC Wood Insert Fire Safety Combustible/Non-combustible MaterialsOverfiring Seasoned WoodACC Wood Insert Burning Process Kindling or First StageSecond Stage Final StageManual Timer Over-Ride ACC Wood Insert Automatic Combustion Control ACCAir Controls Start-Up Air ControlBurn Rates and Operating Efficiency Correct Baffle and Blanket Positions Incorrect Baffle and Blanket PositionsACC Wood Insert Building a Fire ACC Wood Insert Wood Fuel Do not USE Chemicals or Fluids to Start a FireBlower Operating Instructions Frequently Asked Questions ACC Wood Insert Clear SpaceOpacity Smoke Maintenance and Service Chimney and Chimney Connector Inspection/CleaningCleaning Plated Surfaces Disposal of AshesACC Wood Insert Glass Cleaning Inspect Firebrick Cont’dInspect Firebrick Baffle & Blanket Placement Troubleshooting Guide Start Fire Problems Possible Cause SolutionService Parts Replacement Glass Replacement Snap Disc ReplacementACC Wood Insert Blower Replacement Shock RiskACC Wood Insert Door Handle Assembly Baffle & Ceramic Blanket RemovalACC Wood Insert Tube Channel Assembly Replacement Design and Installation Considerations Getting StartedDraft ACC Wood Insert Negative Pressure ACC Wood Insert Locating Your Stove & Chimney Chimney Termination RequirementsACC Wood Insert Rule Flat RoofACC Wood Insert Tools And Supplies Needed Inspect Appliance and ComponentsPre-Use Check List Dimensions and Clearances Appliance DimensionsSideWall Build On-Site Hearth Support Accessory ACC Wood Insert Zero Clearance Floor ProtectionFull Reline RequiredACC Wood Insert Calculating Alternate Floor Protection Chimney Systems Venting SystemsInspections Masonry ChimneyACC Wood Insert Masonry Chimney Cont’d ACC Wood Insert Metal Heat Circulating Masonry Prefabricated Metal Chimney36.1 ACC Wood Insert Prefabricated Metal Chimney Cont’d Securing Chimney ComponentsAltering the Fireplace ACC Wood Insert Zero-Clearance Fireplace Ovalizing Round Stainless Steel LinersChimney Height / Rise and Run Outside Air Kit Installation Items Needed for Installation not suppliedOption One Installation Instructions Option Two Installation InstructionsLeveling Legs Flue AdapterSlide ACC Wood Insert Surround & Trim Kit Installation Cont’d Top Installation InstructionsACC Wood Insert Blower Cord Installation on Left Side InstructionsACC Wood Insert Zero Clearance Adjustable Trim Support Adjustable from 2 inches to 10 inchesShears, Measuring Tape, Gloves Mobile Home Installation Reference Materials Exploded DrawingsFigure a ACC Wood Insert Service Parts & Accessories Important this is Dated Information HOW to OrderStocked At Depot Description Comments Part Number Stocked Description Comments Part NumberFasteners ACC Wood Insert Service And Maintenance Log Date of Service Performed By Description of ServiceContact Information
Top Page Image Contents