Quadra-Fire 7046-137C Listing and Code Approvals, Appliance Certification, Mobile Home Approved

Page 6

2700-I ACC Wood Insert

R

1 Listing and Code Approvals

A. Appliance Certification

Model:

2700-I (ACC) Insert

Laboratory:

OMNI Test Laboratories, Inc.

Report No:

061-S-78-6.2, 061-S-52b-3

Type:

Solid Fuel Type, Listed Room Heater

Standard:

UL1482 and ULC S628-93 and

 

(UM) 84-HUD, Mobile Home

 

Approved.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the UL1482, (UM) 84-HUD and NPFA211 in the U.S.A. and the ULC S628- 93 and CAN/CSA-B365 Installation Codes in Canada.

D. BTU & Efficiency Specifications

EPA Certified:

3.5 grams per hour

Efficiency:

up to 84.1%

BTU Output:

10,450 to 16,400

Heating Capacity:

up to 1800 sq ft depending

 

on climate zone

Vent Size:

6 inches

Firebox Size:

1.75 cubic feet

Max Wood Length:

18 inches

Fuel:

Cord Wood

Shipping Weight:

240 lbs

The Quadra-Fire 2700-I Wood Insert (ACC) meets the U.S. Environmental Protection Agency’s 1990 particulate emis- sion standards.

B. Mobile Home Approved

•This appliance is approved for mobile home installations when not installed in a sleeping room and when an out- side combustion air inlet is provided.

•The structural integrity of the mobile home floor, ceiling, and walls must be maintained.

•The appliance must be properly grounded to the frame of the mobile home with #8 copper ground wire, and use only listed double-wall connector pipe.

•Outside Air Kit, part OAK-ACC must be installed in a mo- bile home installation.

C. Glass Specifications

This stove is equipped with 5mm ceramic glass. Replace glass only with 5mm ceramic glass. Please contact your dealer for replacement glass.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

•Installation and use of any damaged appliance.

•Modification of the appliance.

•Installation other than as instructed by Hearth & Home Technologies.

•Installation and/or use of any component part not approved by Hearth & Home Technologies.

•Operating appliance without fully assembling all components.

•Operating appliance without legs attached (if supplied with unit).

•Do NOT Overfire - If appliance or chimney connector glows, you are overfiring.

Any such action that may cause a fire hazard.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.

For assistance or additional information, consult a qualified installer, service agency or your dealer.

NOTE: Hearth & Home Technologies, manufacturer of this appliance, reserves the right to alter its products, their specifications and/or price without notice.

Quadra-Fire is a registered trademark of Hearth & Home Technologies.

Page

7046-137C

December 15, 2009

Page 5 Page 7
Image 6
Page 5 Page 7
Contents ACC Wood Insert Hot glass will cause burnsACC Wood Insert Serial NumberTable of Contents ACC Wood Insert Warranty Policy ACC Wood Insert Listing and Code Approvals BTU & Efficiency SpecificationsGlass Specifications Appliance CertificationOperating Instructions Your Wood ApplianceOverfiring ACC Wood Insert Fire SafetyCombustible/Non-combustible Materials Seasoned WoodSecond Stage ACC Wood Insert Burning ProcessKindling or First Stage Final StageAir Controls Manual Timer Over-RideACC Wood Insert Automatic Combustion Control ACC Start-Up Air ControlBurn Rates and Operating Efficiency Correct Baffle and Blanket Positions Incorrect Baffle and Blanket PositionsACC Wood Insert Building a Fire ACC Wood Insert Wood Fuel Do not USE Chemicals or Fluids to Start a FireBlower Operating Instructions Frequently Asked Questions ACC Wood Insert Clear SpaceOpacity Smoke Cleaning Plated Surfaces Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Disposal of AshesACC Wood Insert Glass Cleaning Inspect Firebrick Cont’dInspect Firebrick Baffle & Blanket Placement Troubleshooting Guide Start Fire Problems Possible Cause SolutionService Parts Replacement Glass Replacement Snap Disc ReplacementACC Wood Insert Blower Replacement Shock RiskACC Wood Insert Door Handle Assembly Baffle & Ceramic Blanket RemovalACC Wood Insert Tube Channel Assembly Replacement Design and Installation Considerations Getting StartedDraft ACC Wood Insert Negative Pressure ACC Wood Insert Locating Your Stove & Chimney Chimney Termination RequirementsACC Wood Insert Rule Flat RoofACC Wood Insert Tools And Supplies Needed Inspect Appliance and ComponentsPre-Use Check List Dimensions and Clearances Appliance DimensionsSideWall Full Reline Build On-Site Hearth Support AccessoryACC Wood Insert Zero Clearance Floor Protection RequiredACC Wood Insert Calculating Alternate Floor Protection Inspections Chimney SystemsVenting Systems Masonry ChimneyACC Wood Insert Masonry Chimney Cont’d ACC Wood Insert Metal Heat Circulating Masonry Prefabricated Metal Chimney36.1 ACC Wood Insert Prefabricated Metal Chimney Cont’d Securing Chimney ComponentsAltering the Fireplace ACC Wood Insert Zero-Clearance Fireplace Ovalizing Round Stainless Steel LinersChimney Height / Rise and Run Option One Installation Instructions Outside Air Kit InstallationItems Needed for Installation not supplied Option Two Installation InstructionsLeveling Legs Flue AdapterSlide ACC Wood Insert Surround & Trim Kit Installation Cont’d Top Installation InstructionsACC Wood Insert Blower Cord Installation on Left Side InstructionsACC Wood Insert Zero Clearance Adjustable Trim Support Adjustable from 2 inches to 10 inchesShears, Measuring Tape, Gloves Mobile Home Installation Reference Materials Exploded DrawingsFigure a ACC Wood Insert Service Parts & Accessories Important this is Dated Information HOW to OrderStocked At Depot Description Comments Part Number Stocked Description Comments Part NumberFasteners ACC Wood Insert Service And Maintenance Log Date of Service Performed By Description of ServiceContact Information
Top Page Image Contents