Quadra-Fire 7046-137C ACC Wood Insert Prefabricated Metal Chimney Cont’d, Altering the Fireplace

Page 37
250250-2061-2061

R

2700-I ACC Wood Insert

Prefabricated Metal Chimney (Cont’d)

 

Inches

Millimeters

Minimum Width of Cavity Opening - Front

32-1/2

775

Minimum Width of Cavity Opening - Rear

20

508

Minimum Height

18-11/16

475

Minimum Depth from Front to Rear

17-1/4

438

NOTE: Refer to chimney liner manufacturer for recom- mendations on supporting the liner. Installation into fireplaces without a permit will void the listing.

NOTICE: In Canada when using a factory-built chimney it must be safety listed, Type UL103 HT (2100oF) [1149oC] CLASS “A” or conforming to CAN/ULC-S629M, STANDARD FOR 650oC FACTORY-BUILT CHIMNEYS.

WARNING

Fire Risk.

When lining air-cooled factory-built chimneys:.

•Run chimney liner approved to UL 1777 Type HT requirements (2100 degrees F)

•Re-install original factory built chimney cap

ONLY

•DO NOT block cooling air openings in chimney

•Blocking cooling air will overheat the chimney

G. Securing Chimney Components

All joints should be secured with 3 sheet metal screws or rivets per pipe manufacturers instructions. The sections must be attached to the insert and to each other with the crimped (male) end pointing toward the insert. Figure 37.1.

LINER CONNECTOR

CRIMPED

FLUE

END

GAS

TOWARDS

DIRECTION

STOVE

 

Figure 37.1

H. Altering the Fireplace

The following modifications of factory-built fireplaces are permissible:

The following parts may be removed:

Damper

Smoke Shelf or Baffle

Ember Catches

Fire Grate

Viewing Screen/Curtain

Doors

•The fireplace must not be altered, except that the damper may be removed to accommodate a direct-connect starter pipe or chimney liner,

•External trim pieces which do not affect the operation of the fireplace may be removed providing they can be stored on or within the fireplace for reassembly if the insert is removed.

To maintain the functionality of the fireplace’s chimney system you may use a Simpson Dura-Vent DuraLiner Slip Hanger, Part # 4671, and attach to the bottom of the fireplace chimney cap to support the liner. You have two options to completing the installation.

Option one - Not required to use liner cap: Re-attach the existing top of the chimney cap.

Option two - Using liner cap:

Re-attach the existing top of the chimney cap and install a new storm collar and a new liner cap.

•The permanent metal warning label provided in the component pack must be attached to the back of the fireplace, with screws or nails, stating that the fireplace may have been altered to accommodate the insert, and must be returned to original condition for use as a conventional fireplace. Figure 37.2.

•If the hearth extension is lower than the fireplace opening, the portion of the insert extending onto the hearth must be supported.

•Manufacturer designed adjustable support kit can be ordered from your dealer.

•Final approval of this installation type is contingent upon the authority having jurisdiction.

WARNING! Risk of Fire!

Follow venting manufacturer’s clearances and instructions when installing venting system.

WARNING

THIS FIREPLACE MAY HAVE BEEN ALTERED TO ACCOMMODATE AN INSERT. IT MUST BE RETURNED TO ITS ORIGINAL CONDITION BEFORE USE AS A SOLID FUEL BURNING FIREPLACE.

Figure 37.2

December 15, 2009

7046-137C

Page 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Hot glass will cause burns ACC Wood InsertSerial Number ACC Wood InsertTable of Contents ACC Wood Insert Warranty Policy ACC Wood Insert Glass Specifications BTU & Efficiency SpecificationsListing and Code Approvals Appliance CertificationYour Wood Appliance Operating InstructionsCombustible/Non-combustible Materials ACC Wood Insert Fire SafetyOverfiring Seasoned WoodKindling or First Stage ACC Wood Insert Burning ProcessSecond Stage Final StageACC Wood Insert Automatic Combustion Control ACC Manual Timer Over-RideAir Controls Start-Up Air ControlBurn Rates and Operating Efficiency Incorrect Baffle and Blanket Positions Correct Baffle and Blanket PositionsACC Wood Insert Building a Fire Do not USE Chemicals or Fluids to Start a Fire ACC Wood Insert Wood FuelBlower Operating Instructions ACC Wood Insert Clear Space Frequently Asked QuestionsOpacity Smoke Chimney and Chimney Connector Inspection/Cleaning Maintenance and ServiceCleaning Plated Surfaces Disposal of AshesInspect Firebrick Cont’d ACC Wood Insert Glass CleaningInspect Firebrick Baffle & Blanket Placement Start Fire Problems Possible Cause Solution Troubleshooting GuideGlass Replacement Snap Disc Replacement Service Parts ReplacementShock Risk ACC Wood Insert Blower ReplacementBaffle & Ceramic Blanket Removal ACC Wood Insert Door Handle AssemblyACC Wood Insert Tube Channel Assembly Replacement Getting Started Design and Installation ConsiderationsDraft ACC Wood Insert Negative Pressure Chimney Termination Requirements ACC Wood Insert Locating Your Stove & ChimneyFlat Roof ACC Wood Insert RuleInspect Appliance and Components ACC Wood Insert Tools And Supplies NeededPre-Use Check List Appliance Dimensions Dimensions and ClearancesSideWall ACC Wood Insert Zero Clearance Floor Protection Build On-Site Hearth Support AccessoryFull Reline RequiredACC Wood Insert Calculating Alternate Floor Protection Venting Systems Chimney SystemsInspections Masonry ChimneyACC Wood Insert Masonry Chimney Cont’d Prefabricated Metal Chimney ACC Wood Insert Metal Heat Circulating Masonry36.1 Securing Chimney Components ACC Wood Insert Prefabricated Metal Chimney Cont’dAltering the Fireplace Ovalizing Round Stainless Steel Liners ACC Wood Insert Zero-Clearance FireplaceChimney Height / Rise and Run Items Needed for Installation not supplied Outside Air Kit InstallationOption One Installation Instructions Option Two Installation InstructionsFlue Adapter Leveling LegsSlide Top Installation Instructions ACC Wood Insert Surround & Trim Kit Installation Cont’dInstructions ACC Wood Insert Blower Cord Installation on Left SideAdjustable from 2 inches to 10 inches ACC Wood Insert Zero Clearance Adjustable Trim SupportShears, Measuring Tape, Gloves Mobile Home Installation Exploded Drawings Reference MaterialsFigure a Important this is Dated Information HOW to Order ACC Wood Insert Service Parts & AccessoriesStocked At Depot Description Comments Part Number Description Comments Part Number StockedFasteners Date of Service Performed By Description of Service ACC Wood Insert Service And Maintenance LogContact Information
Top Page Image Contents