Quadra-Fire 7046-137C warranty Blower Operating Instructions

Page 15

R

2700-I ACC Wood Insert

M.Blower Control Box & Snap Disc Operating Instructions

1.The blower will turn on/off automatically when set to AUTO. Figure 15.1.

2.When set to MANUAL, the fan will turn on/off only when you turn it on or off. This setting over-rides the internal snap disc.

3.Adjust the speed of the fan by turning the HIGH/LOW knob to the desired setting.

MANUAL: Over-rides the internal Snap Disc

AUTO: Fan will turn ON/OFF automatically and is controlled by the internal Snap Disc

N. Blower Operating Instructions

Figure 15.1

1.Initial (cold) startup: Open both controls fully by rais- ing the Burn Rate Air Control all the way up until it stops and PUSH the Start-up Air Control back until it stops. The blower tends to cool the appliance. Leave the blower off until the burn is well established, i.e., 30 minutes.

2. High Burn Setting: Both controls are open. Burn Rate Air Control is pulled up and the Start-up Air Control is fully pushed in. Blower may remain on.

3.Medium-High Burn Setting*: Burn Rate Air Control is closed then opened to 1 inch to fully open (pull up). Blower may remain on.

4.Medium-Low Burn Setting*: Burn Rate Air Control is closed then opened to 1/4 inch to 1/2 inch (pull up). Leave the blower off until the burn is well established, i.e., 30 minutes.

5.Low Burn Setting*: Burn Rate Air Control is closed (down position). Leave the blower off until the burn is well established, i.e., 30 minutes.

*NOTE: For burn settings 3 to 5 the Start-up Air Control needs to be pushed in (Open) then pulled forward to activate the Automatic Combustion Control (ACC).

NOTE: For maximum efficiency and lowest emissions, when operating the blower in either the automatic or manual setting for the low and medium low burn settings leave the blower off until the burn is well established, i.e., 30 minutes.

6.The blower is equipped with a rheostat (speed control). The highest blower speed is obtained by turning the rheostat on, then adjusting back towards “OFF” as far as possible without turning the blower off. For a low blower speed, turn the control knob clockwise as far as possible

NOTICE!

Do NOT operate a circulating fan within close proxim- ity, approximately 4 ft (1.2m), of appliance

•Can reverse air flow, blowing hot air into appliance cavity.

•Can damage appliance blower due to overheating.

December 15, 2009

7046-137C

Page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Hot glass will cause burns ACC Wood InsertSerial Number ACC Wood InsertTable of Contents ACC Wood Insert Warranty Policy ACC Wood Insert Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Listing and Code ApprovalsYour Wood Appliance Operating InstructionsSeasoned Wood ACC Wood Insert Fire SafetyCombustible/Non-combustible Materials OverfiringFinal Stage ACC Wood Insert Burning ProcessKindling or First Stage Second StageStart-Up Air Control Manual Timer Over-RideACC Wood Insert Automatic Combustion Control ACC Air ControlsBurn Rates and Operating Efficiency Incorrect Baffle and Blanket Positions Correct Baffle and Blanket PositionsACC Wood Insert Building a Fire Do not USE Chemicals or Fluids to Start a Fire ACC Wood Insert Wood FuelBlower Operating Instructions Frequently Asked Questions ACC Wood Insert Clear SpaceOpacity Smoke Disposal of Ashes Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Cleaning Plated SurfacesACC Wood Insert Glass Cleaning Inspect Firebrick Cont’dInspect Firebrick Baffle & Blanket Placement Start Fire Problems Possible Cause Solution Troubleshooting GuideGlass Replacement Snap Disc Replacement Service Parts ReplacementShock Risk ACC Wood Insert Blower ReplacementBaffle & Ceramic Blanket Removal ACC Wood Insert Door Handle AssemblyACC Wood Insert Tube Channel Assembly Replacement Design and Installation Considerations Getting StartedDraft ACC Wood Insert Negative Pressure Chimney Termination Requirements ACC Wood Insert Locating Your Stove & ChimneyFlat Roof ACC Wood Insert RuleACC Wood Insert Tools And Supplies Needed Inspect Appliance and ComponentsPre-Use Check List Appliance Dimensions Dimensions and ClearancesSideWall Required Build On-Site Hearth Support AccessoryACC Wood Insert Zero Clearance Floor Protection Full RelineACC Wood Insert Calculating Alternate Floor Protection Masonry Chimney Chimney SystemsVenting Systems InspectionsACC Wood Insert Masonry Chimney Cont’d ACC Wood Insert Metal Heat Circulating Masonry Prefabricated Metal Chimney36.1 ACC Wood Insert Prefabricated Metal Chimney Cont’d Securing Chimney ComponentsAltering the Fireplace ACC Wood Insert Zero-Clearance Fireplace Ovalizing Round Stainless Steel LinersChimney Height / Rise and Run Option Two Installation Instructions Outside Air Kit InstallationItems Needed for Installation not supplied Option One Installation InstructionsFlue Adapter Leveling LegsSlide Top Installation Instructions ACC Wood Insert Surround & Trim Kit Installation Cont’dInstructions ACC Wood Insert Blower Cord Installation on Left SideACC Wood Insert Zero Clearance Adjustable Trim Support Adjustable from 2 inches to 10 inchesShears, Measuring Tape, Gloves Mobile Home Installation Exploded Drawings Reference MaterialsFigure a Important this is Dated Information HOW to Order ACC Wood Insert Service Parts & AccessoriesStocked At Depot Description Comments Part Number Stocked Description Comments Part NumberFasteners Date of Service Performed By Description of Service ACC Wood Insert Service And Maintenance LogContact Information
Top Page Image Contents