Quadra-Fire 7046-137C warranty ACC Wood Insert Zero Clearance Adjustable Trim Support

Page 44

2700-I ACC Wood Insert

 

R

 

 

I. Zero Clearance Adjustable Trim Support,

EXPLODED VIEW OF SCISSORS

Adjustable from 2 inches to 10 inches

 

 

Part No. ADJSPT-3, size 3-1/2” x 48-1/2”

 

 

Included in Kit: (1) Trim Top, (1) Trim Front, (2) Trim Sides,

 

SCREWS ARE CIRCLED

 

 

Double-Sided Tape (already installed)

 

 

Tools Needed: Phillips Head Screwdriver, Sheet Metal

DOUBLE-SIDED TAPE

DOUBLE-SIDED TAPE

Shears, Measuring Tape, Gloves

Figure 44.1

 

 

 

1.The 10 screws on each set of scissors will already be loose when shipped. Figure 44.1.

2.Expand scissors to desired height. Tighten screws to hold in place using Phillips Head screwdriver. See

Figure 44.2.

3.Measure front and side trims to required height to cover scissors and mark pieces for cutting. Cut excess mate- rial from top of trim’s edge, not bottom. This edge will be sharp; wear gloves to prevent injury to your hands.

Figure 44.2.

4.Using sheet metal shears, cut trim along the marked edge. The cut edge fits under lip of top trim, so it allows for some variance in your straight edge.

5.The double-sided tape that holds front and side trims to scissors has a particularly powerful bonding adhe- sive. Adjustments are extremely difficult once trim has adhered to tape. Do a dry run first without removing paper from tape.

6.Place cut edge of trim under top lip and into position on scissors. Place side pieces on first and then front piece. The front piece overlaps side pieces.

7.Once you are satisfied with the positioning, remove trim and set aside.

8.Remove the paper from double-sided tape that is to accept trim side. Align side and then press hard against tape to secure side piece. Repeat for other side. Install front trim piece last.

9.There are 3 holes in the back flange of the top to secure it to the wall if necessary. Use the appropriate fastener for the type of wall material, i.e., brick, sheet- rock, etc.

EXPAND SCISSORS TO DESIRED HEIGHT

INSTALL FRONT TRIM

CUT TOP EDGE

LAST. CORNERS

OF TRIM, NOT

OVERLAP SIDE TRIM

BOTTOM EDGE

PIECES

 

Figure 44.2

Figure 44.3 - Installation Complete

Page 44

7046-137C

December 15, 2009

Page 43 Page 45
Image 44
Page 43 Page 45
Contents ACC Wood Insert Hot glass will cause burnsACC Wood Insert Serial NumberTable of Contents ACC Wood Insert Warranty Policy ACC Wood Insert BTU & Efficiency Specifications Glass SpecificationsListing and Code Approvals Appliance CertificationOperating Instructions Your Wood ApplianceACC Wood Insert Fire Safety Combustible/Non-combustible MaterialsOverfiring Seasoned WoodACC Wood Insert Burning Process Kindling or First StageSecond Stage Final StageManual Timer Over-Ride ACC Wood Insert Automatic Combustion Control ACCAir Controls Start-Up Air ControlBurn Rates and Operating Efficiency Correct Baffle and Blanket Positions Incorrect Baffle and Blanket PositionsACC Wood Insert Building a Fire ACC Wood Insert Wood Fuel Do not USE Chemicals or Fluids to Start a FireBlower Operating Instructions Opacity Smoke Frequently Asked QuestionsACC Wood Insert Clear Space Maintenance and Service Chimney and Chimney Connector Inspection/CleaningCleaning Plated Surfaces Disposal of AshesInspect Firebrick ACC Wood Insert Glass CleaningInspect Firebrick Cont’d Baffle & Blanket Placement Troubleshooting Guide Start Fire Problems Possible Cause SolutionService Parts Replacement Glass Replacement Snap Disc ReplacementACC Wood Insert Blower Replacement Shock RiskACC Wood Insert Door Handle Assembly Baffle & Ceramic Blanket RemovalACC Wood Insert Tube Channel Assembly Replacement Draft Design and Installation ConsiderationsGetting Started ACC Wood Insert Negative Pressure ACC Wood Insert Locating Your Stove & Chimney Chimney Termination RequirementsACC Wood Insert Rule Flat RoofPre-Use Check List ACC Wood Insert Tools And Supplies NeededInspect Appliance and Components Dimensions and Clearances Appliance DimensionsSideWall Build On-Site Hearth Support Accessory ACC Wood Insert Zero Clearance Floor ProtectionFull Reline RequiredACC Wood Insert Calculating Alternate Floor Protection Chimney Systems Venting SystemsInspections Masonry ChimneyACC Wood Insert Masonry Chimney Cont’d 36.1 ACC Wood Insert Metal Heat Circulating MasonryPrefabricated Metal Chimney Altering the Fireplace ACC Wood Insert Prefabricated Metal Chimney Cont’dSecuring Chimney Components Chimney Height / Rise and Run ACC Wood Insert Zero-Clearance FireplaceOvalizing Round Stainless Steel Liners Outside Air Kit Installation Items Needed for Installation not suppliedOption One Installation Instructions Option Two Installation InstructionsLeveling Legs Flue AdapterSlide ACC Wood Insert Surround & Trim Kit Installation Cont’d Top Installation InstructionsACC Wood Insert Blower Cord Installation on Left Side InstructionsShears, Measuring Tape, Gloves ACC Wood Insert Zero Clearance Adjustable Trim SupportAdjustable from 2 inches to 10 inches Mobile Home Installation Reference Materials Exploded DrawingsFigure a ACC Wood Insert Service Parts & Accessories Important this is Dated Information HOW to OrderStocked At Depot Description Comments Part Number Fasteners StockedDescription Comments Part Number ACC Wood Insert Service And Maintenance Log Date of Service Performed By Description of ServiceContact Information
Top Page Image Contents