Quadra-Fire 7046-137C warranty ACC Wood Insert Blower Cord Installation on Left Side, Instructions

Page 43

R

2700-I ACC Wood Insert

H. Blower Cord Installation on Left Side

The blower cord is shipped to be installed on the right side of the appliance. You may relocate the cord so it is on the left side. You remove the blower control plate and wire har- ness as one assembly and reconnect on the left side. The cover plate on the left side is re-attached on the right side.

Instructions

1.Remove the blower assembly from the appliance. Using a 5/32 Allen wrench remove the 4 mounting bolts and slide the assembly towards you.

2.Using needle nose pliers bend the tabs up that holds the wire harness in place and remove the wires. There are 2 tabs, one at the top of the assembly and one at the bottom.

3.Disconnect the power leads to the blower.

4.Remove the snap disc mounting plate by removing the 2 sheet metal screws with a Phillips head screw driver.

5.Disconnect the spade terminals to the snap disc.

6.Remove the blower control plate using a flat head screw driver to remove the 2 screws, 1 on the top and 1 on the bottom. Remove the blower control plate and wire har- ness at the same time.

7.On the left end of the blower housing, remove the cover plate and re-install on the right end of the housing.

8.Install the blower control plate on the left end and secure the wire harness underneath the tabs on the left side and bend the tabs back into position.

9.Re-connect the spade terminals to the snap disc and re- install the snap disc assembly.

10.Re-connect the power leads to the blower.

Snap Disc Location

Remove Bolts and Slide

Blower Assembly Out

Figure 43.1


			Snap Disc
			Snap Disc			Blower
			Mounting Plate			Blower
			Mounting Plate			Control
Cover						Control
Cover						Plate
Plate						Plate
Plate		Snap Disc
		Snap Disc

Wire Harness Tabs Locations

Left Side	Right Side

Figure 43.2

Bend Wire Harness Tab

Figure 43.3

Snap Disc

Mounting Plate

Disconnect Spade

Terminals from Snap Disc

Figure 43.4

Figure 43.5 - Installed on Left Side

December 15, 2009

7046-137C

Page 43

Image 43

Contents Hot glass will cause burns ACC Wood InsertSerial Number ACC Wood InsertTable of Contents ACC Wood Insert Warranty Policy ACC Wood Insert Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Listing and Code ApprovalsYour Wood Appliance Operating InstructionsSeasoned Wood ACC Wood Insert Fire SafetyCombustible/Non-combustible Materials OverfiringFinal Stage ACC Wood Insert Burning ProcessKindling or First Stage Second StageStart-Up Air Control Manual Timer Over-RideACC Wood Insert Automatic Combustion Control ACC Air ControlsBurn Rates and Operating Efficiency Incorrect Baffle and Blanket Positions Correct Baffle and Blanket PositionsACC Wood Insert Building a Fire Do not USE Chemicals or Fluids to Start a Fire ACC Wood Insert Wood FuelBlower Operating Instructions ACC Wood Insert Clear Space Frequently Asked QuestionsOpacity Smoke Disposal of Ashes Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Cleaning Plated SurfacesInspect Firebrick Cont’d ACC Wood Insert Glass CleaningInspect Firebrick Baffle & Blanket Placement Start Fire Problems Possible Cause Solution Troubleshooting GuideGlass Replacement Snap Disc Replacement Service Parts ReplacementShock Risk ACC Wood Insert Blower ReplacementBaffle & Ceramic Blanket Removal ACC Wood Insert Door Handle AssemblyACC Wood Insert Tube Channel Assembly Replacement Getting Started Design and Installation ConsiderationsDraft ACC Wood Insert Negative Pressure Chimney Termination Requirements ACC Wood Insert Locating Your Stove & ChimneyFlat Roof ACC Wood Insert RuleInspect Appliance and Components ACC Wood Insert Tools And Supplies NeededPre-Use Check List Appliance Dimensions Dimensions and ClearancesSideWall Required Build On-Site Hearth Support AccessoryACC Wood Insert Zero Clearance Floor Protection Full RelineACC Wood Insert Calculating Alternate Floor Protection Masonry Chimney Chimney SystemsVenting Systems InspectionsACC Wood Insert Masonry Chimney Cont’d Prefabricated Metal Chimney ACC Wood Insert Metal Heat Circulating Masonry36.1 Securing Chimney Components ACC Wood Insert Prefabricated Metal Chimney Cont’dAltering the Fireplace Ovalizing Round Stainless Steel Liners ACC Wood Insert Zero-Clearance FireplaceChimney Height / Rise and Run Option Two Installation Instructions Outside Air Kit InstallationItems Needed for Installation not supplied Option One Installation InstructionsFlue Adapter Leveling LegsSlide Top Installation Instructions ACC Wood Insert Surround & Trim Kit Installation Cont’dInstructions ACC Wood Insert Blower Cord Installation on Left SideAdjustable from 2 inches to 10 inches ACC Wood Insert Zero Clearance Adjustable Trim SupportShears, Measuring Tape, Gloves Mobile Home Installation Exploded Drawings Reference MaterialsFigure a Important this is Dated Information HOW to Order ACC Wood Insert Service Parts & AccessoriesStocked At Depot Description Comments Part Number Description Comments Part Number StockedFasteners Date of Service Performed By Description of Service ACC Wood Insert Service And Maintenance LogContact Information