Monessen Hearth ILDV20PV, ILDV20NV Product features and code approval, Product Specifications

Page 5

product features and code approval

ILDV20/ILDV30 Fireplace Insert

product SPECIFICATIONS

•This appliance has been certified for use with either natural or propane gas. Refer to the appropriate data plates.

•This appliance is not for use with solid fuels.

•The appliance is approved for bedroom or bedsitting room installations.

•The appliance must be installed in accordance with local codes if any. If none exist use the current installation code. ANSI Z223.1/NFPA 54 in the USA, CSA B149 in Canada.

•This appliance is mobile home appr-oved.

•The appliance must be properly con- nected to a venting system.

• The appliance is not approved for closet or recessed installations.

Figure 1 -

ILDV Series Fireplace Insert

Blower

Gas Shut-

Off Valve

Blower Knob

ON/OFF

Switch

OFF/Pilot/ON

Knob

HI/LO Knob

Piezo

Code Approval

Direct Vent type appliances draw all combustion air from outside of the dwelling through the vent pipe.

These appliances have been tested by CSA and found to comply with the established standards for DIRECT VENT GAS FIREPLACE HEATERS in the USA and Canada as follows:

LISTED VENTED GAS FIREPLACE HEATER

TESTED TO: ANSI Z21.88b-2008/CSA 2.33b-2008 STANDARDS

A manufactured home (USA only) or mobile home OEM installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or when such a standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4.

83D0511

Image 5

Contents What to do if YOU Smell GAS Ildv Series Direct Vent Gas Fireplace InsertInstallation General Installation InformationVent Installation Insert InstallationOwner Important Safety InformationInstaller Non-utility gas wells. This Never connect unit to privateGas is commonly known as Wellhead gasListed Vented GAS Fireplace Heater Product features and code approvalProduct Specifications Orifice SIZES, Pressures and BTUs High ElevationsBefore You Start ILDV20NV ILDV20PV ILDV30NV ILDV30PVILDV20 ILDV30 Insert dimensionsInsert Applications General installation InformationInsert Clearances ClearancesMantel clearances Hearth RequirementsInsert Placement ZERO-CLEARANCE Metal Fireplace Requirements InstallationInstallation Precautions Vent installationVent Requirements Combustion which can create a safety hazard. Consult your Failure to adjust air shutter properly may lead to improperDealer or installer if you suspect an improperly adjusted Altitude ConsiderationsVent Configurations Remove Manifold and Attach to Flex Vent Manifold Removal and InstallationCheck gas type Insert InstallationTo liquid petroleum LP gas Insert installationUse pipe joint sealant that is resistant Check for gas leaks Check GAS PressureDo not use open flame to Hand Held Remote Control Remote Wall mounted SwitchDo not use the entire bag of rock wool to cover burner area Log placementInstalling Logs and Rock Wool Ember Material in Firebox Place Log #6 Place Log #5 Install Surround Surround installationWhat to do if YOU Smell GAS Operating InstructionsInitial lighting Never use an open flame to check for gas leakLighting pilot Approved leak testing methodPilot position Main burner switchLighting the burner Adjust the AIR Shutter Glass Frame Removal Glass Frame RemovalBlower Replacement 20ILDV 30ILDV Blower Parts ListCleaning glass Cleaning and MaintenanceRelight pilot. Refer to Maintenance Replacement Parts Replacement Parts Observed Problem Possible Cause Remedy TroubleshootingILDV20/ILDV30 Fireplace Insert Five Year Warranty Lifetime WarrantyBasic Warranty If Warranty Service is NeededAFUE% Mhsc