Barnett Engineering ARU CV2 instruction manual Indicators, Troubleshooting

Page 8
On power-up, following the initial flashing of each LED, Hook flashes until the Cv2 has found cellular service. Once the unit has logged onto the cellular network, the Hook indicator goes out. Hook also flashes while a call is being placed. After the call has been processed, Hook is on steady until the end of the call when it goes out.
Tone blinks once for each DTMF digit that is either received or transmitted.
Voice is on when the Cv2 is speaking. On power-up, following the initial flashing of each LED, it will go on continuously for 2 seconds if any section of the stored database, voice or vocabulary memory is corrupt. If this occurs, the configuration should be downloaded into the unit and the voice recordings checked for validity. Voice flashes briefly every second to indicate that the Cv2 is operating correctly.

Operations Overview

1-6

1.9 Indicators

The Cv2 has four LED indicators to show the operation of the unit and assist in troubleshooting.

When the Cv2 is initially powered up, the four LEDs will do the following:

&All will turn on for approximately one second.

&Hook will flash on and off for one second then go out.

&Tone will flash on and off for one second then go out.

&Voice will flash on and off for one second then go out.

&Alarm will flash on and off for one second then go out.

& Hook

& Tone

& Voice

&Alarm If an unacknowledged alarm is present, the alarm indicator will flash. When the alarm is acknowledged, Alarm is on steady. When no alarms are present, Alarm is off.

1.10Troubleshooting

Is there power to the unit?

When power is first applied to the Cv2, it will flash the Hook indicator until it establishes contact with the cellular service. At any other time, the presence of power, and correct operation, are indicated by the brief flashing of the Voice LED every second.

Does the cell phone work?

Use the local call feature to determine if the unit is working properly. If the call cannot be completed, query the cell phone to see if it responds - any parameter can be used here. Query the RSSI (Received Signal Strength Indicator) in the phone to see if there is coverage in the area. The message “error” will be returned if there is no coverage. This can possibly be corrected by improving the antenna system.

B1272M001

BARNETT ENGINEERING LTD.

ProTalk Cv2

Image 8
Contents 3UR7DON 1272M001Contents What constitutes an alarm? Cv2 CapabilitiesHow are alarms processed? Way in which the Cv2 processes alarms is shown in FigureWhat actions should occur when an alarm is detected? How do you want to respond to an alarm call? Sending remote control commands What if an alarm is not acknowledged?What do you want the Cv2 to do when you call it? Indicators TroubleshootingAre the inputs connected properly? Packaged model Antenna requirementsMounting Stand-alone model Ground closure alarm signalInput port connections Analog input 2 +12 volt alarm signal3 +5 volt alarm signal Configuration programming connection Output port connectionsStand-alone Cv2 Installing the program Starting the configuration programDesktop and how to access programming functions PC requirementsFile Operations HardwareGeneral GroupsConfiguring the Cv2 DirectoriesProgramming Hardware sectionTotalizer Input Watchdog InputInterval Input Points section On/Off OutputTimed Output Point Name Common Settings for Points Port SelectionUsing Group Enabled Alarm StateDigital and Watchdog Points Dtmf TagAnalog Point Clear CodeUnits Decimal Values CalibrateBinary Values Dtmf On Code HysteresisOn/Off Output Point Group section Dtmf Off CodeTimed Output Point Enable This Group Enable Auto AckGroup Name Acknowledge CodeEnable Ack Request TimersShort Timer Long TimerAlarm Active New AlarmSpecial Function Outputs Acknowledge ReceivedDial WaitAuto Ack AlertVoice AnswerSignal Access CodeDelete Site NameCall Progress Shift Change CodeTemporary Acknowledge Time Vocabulary Configuration DataVoice Messages Commands SetupAccess Dial Cv2 Site ID is Ajax Compressor Station Cv2 Electrical on or Electrical OFF Telset Programming Summary Exit Record Points Query NAM Specifications Programmable FeaturesTelephone OptionsWarranty