Directed Electronics SR6000 manual System features learn routine

Page 39

Pressing a fourth time within five seconds: The siren chirps four times followed by a long chirp. Zones Two and Four are now bypassed.

■ Pressing a fifth time within five seconds: The siren chirps five times followed by a long chirp. All input zones, except the ignition, are now bypassed.

system features learn routine

The System Features Learn Routine™ dictates how the unit operates. Due to the number of features, the

features have been divided into three menus. It is possible to access and change any of the feature set- tings using the Valet®/Program switch. However, this process can be greatly simplified by using the ProSecurity Programmer. Any of the settings can be changed and then assigned to one of up to four transmitters, a feature called Owner Recognition. Each time that particular transmitter is used to disarm the system, the assigned feature settings will be recalled. Owner Recognition is only possible when programming the unit via the ProSecurity Programmer.

The learn routine may be locked if previously programmed using the ProSecurity Programmer. If the horn

generates one long honk when attempting to program the unit, the learn routine is locked and must be unlocked using the ProSecurity Programmer before proceeding.

To program the features using the Valet switch:

1.Open a door. (The GREEN wire, H1/5, or the VIOLET, H1/7 must be connected.)

2.Key. Turn the ignition on and then back off.

3. Select Menu. Press and HOLD the Valet®/Program switch. When the LED flashes once and the siren chirps, Menu One has been selected. Continue to hold the switch until the LED flashes twice and the siren chirps twice, Menu Two has now been selected. Continue to hold the switch until the LED flashes three times and the siren chirps three times, Menu Three has now been selected. Release the switch after the Menu choice has been selected.

4. Choose. Within 10 seconds, press and release the Valet®/Program switch the number of times corresponding to the feature number you want to program and then press and hold the switch. (See Feature Menus.)

After a second, the LED will flash to indicate which feature you have accessed. For example, in Menu Two, groups of eight flashes would indicate access to the activation pulse setting (Feature 2-8). The horn will also honk eight times (if connected).

39

Image 39
Contents ProSecurity Page Table of contents Page Installation points to remember Before beginning the installationAfter the installation Locations for the control module Locations for the sirenLocations for stinger doubleguard shock sensor Locations for the status LED Locations for valet/program switchObtaining constant Finding the wires you needLocations for the optional starter kill relay Locations for the relay satelliteFinding the starter wire Finding the 12V switched ignition wireFinding the accessory wire Finding the tachometer wireFinding the wait-to-start bulb wire for diesels Finding the door pin switch circuit Finding a + parking light wireMaking your wiring connections Auxiliary harness H2, 6-pin connector Door lock harness, 3-pin connector Heavy gauge relay satellite wiring diagram Primary harness H1 wire connection guide H1/3 WHITE/BLUE remote start activation input H1/5 Green door trigger input, zone H1/8 Black chassis ground connection Secondary harness H2 wire connection guide Page Relay key satellite interface wire connection guide Connect this wire to the ignition wire in the vehicle Remote start secondary harness H3 wire con- nection guide Figure a Neutral safety switch interfaceTesting the neutral safety switch Sense wire shutting down the unit prematurely Directed Electronics, Inc. Vista, CA Bypassing GM vehicle anti-theft systems Vats Passkey III PK-3, transponder-based systems Passlock I and passlock II PL-1 and PL-2Plug-in LED and valet/program switch Shock sensor harness, 4-pin connector Programming jumpers Tach learningLight flash + Tach threshold on/offFunction Wire Color Standard configuration Transmitter configurationsPressing Multi-level security armingSystem features learn routine Tings. The sire will chirp once if connected. Pressing Menu #1 basic features Feature menusMenu #3 remote start options Menu #2 advanced featuresFeature descriptions Menu #2 advanced features Page Tion from 1-60 minutes Page Nuisance prevention circuitry Valet modeTable of zones Timer modeShutdown diagnostics To perform shutdown diagnosticsLong term event history Safety check Alarm troubleshooting TroubleshootingRemote start troubleshooting Page Wiring quick reference guide Quick reference guide Get Started Get Protected