Directed Electronics SR6000 manual

Page 4

warning! safety first

The following safety warnings must be observed at all times:

Due to the complexity of this system, installation of this product must only be performed by an authorized Ungo dealer.

When properly installed, this system can start the vehicle via a command signal from the remote control transmitter. Therefore, never operate the system in an area that does not have adequate ventilation. The fol- lowing precautions are the sole responsibility of the user; however, authorized Ungo dealers should make the following recommendations to all users of this system:

1.Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).

2.When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch.

3.It is the user's sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle.

4.THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED.

Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user will be responsible for having the neutral safety feature of the vehicle period- ically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Ungo dealer in accordance with the Safety Check outlined in this product instal- lation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.

After the remote start module has been installed, test the remote start module in accordance with the Safety Check outlined in this installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or properly reinstalled so that the vehicle does not start in gear. All installations must be performed by an authorized Ungo dealer. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CON-

TRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. UNGO WILL NOT BE HELD RESPON- SIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

4

Image 4
Contents ProSecurity Page Table of contents Page Before beginning the installation Installation points to rememberAfter the installation Locations for the siren Locations for the control moduleLocations for stinger doubleguard shock sensor Locations for valet/program switch Locations for the status LEDFinding the wires you need Locations for the optional starter kill relayLocations for the relay satellite Obtaining constantFinding the 12V switched ignition wire Finding the starter wireFinding the tachometer wire Finding the accessory wireFinding the wait-to-start bulb wire for diesels Finding a + parking light wire Finding the door pin switch circuitMaking your wiring connections Auxiliary harness H2, 6-pin connector Door lock harness, 3-pin connector Heavy gauge relay satellite wiring diagram Primary harness H1 wire connection guide H1/3 WHITE/BLUE remote start activation input H1/5 Green door trigger input, zone H1/8 Black chassis ground connection Secondary harness H2 wire connection guide Page Relay key satellite interface wire connection guide Connect this wire to the ignition wire in the vehicle Remote start secondary harness H3 wire con- nection guide Neutral safety switch interface Figure aTesting the neutral safety switch Sense wire shutting down the unit prematurely Directed Electronics, Inc. Vista, CA Bypassing GM vehicle anti-theft systems Vats Passlock I and passlock II PL-1 and PL-2 Passkey III PK-3, transponder-based systemsPlug-in LED and valet/program switch Shock sensor harness, 4-pin connector Tach learning Programming jumpersTach threshold on/off Light flash +Function Wire Color Transmitter configurations Standard configurationMulti-level security arming PressingSystem features learn routine Tings. The sire will chirp once if connected. Pressing Feature menus Menu #1 basic featuresMenu #2 advanced features Menu #3 remote start optionsFeature descriptions Menu #2 advanced features Page Tion from 1-60 minutes Page Valet mode Nuisance prevention circuitryTimer mode Table of zonesTo perform shutdown diagnostics Shutdown diagnosticsLong term event history Safety check Troubleshooting Alarm troubleshootingRemote start troubleshooting Page Wiring quick reference guide Quick reference guide Get Started Get Protected