Directed Electronics SR6000 manual Heavy gauge relay satellite wiring diagram

Page 16

heavy gauge relay satellite wiring diagram

		______
	1	______	PURPLE	(+) STARTER OUTPUT TO STARTER (STARTER SIDE)
	1		PURPLE	(+) STARTER OUTPUT TO STARTER (STARTER SIDE)
		______

	2		GREEN	STARTER INPUT FROM IGNITION (KEY SIDE)
	2		GREEN	STARTER INPUT FROM IGNITION (KEY SIDE)
		______

	3		RED	(+) HIGH CURRENT 12V INPUT
	3		RED	(+) HIGH CURRENT 12V INPUT
		______

	4		ORANGE	(+) OUTPUT TO ACCESSORY CIRCUIT
	4		ORANGE	(+) OUTPUT TO ACCESSORY CIRCUIT
		______

	5		PINK	(+) OUTPUT TO PRIMARY IGNITION CIRCUIT
	5		PINK	(+) OUTPUT TO PRIMARY IGNITION CIRCUIT
		______

	6		RED	(+) (30A) HIGH CURRENT 12V INPUT
	6		RED	(+) (30A) HIGH CURRENT 12V INPUT
	7	______

			PINK/WHITE	(+) OUTPUT TO SECOND IGNITION CIRCUIT
			PINK/WHITE	(+) OUTPUT TO SECOND IGNITION CIRCUIT
	8	______

			RED/WHITE	(+) (30A) HIGH CURRENT 12V INPUT
			RED/WHITE	(+) (30A) HIGH CURRENT 12V INPUT

remote start harness (H3), 5-pin connector

		______
	H3/1	______	BLUE/WHITE	(-) 200 mA 2ND STATUS/REAR DEFOGGER- LATCHED/PULSED
	H3/2	______

			GRAY	(-) HOOD PINSWITCH INPUT, ZONE 1
	H3/3	______

			BROWN	(+) BRAKE SHUTDOWN WIRE
	H3/4	______

			VIOLET/WHITE	TACHOMETER INPUT WIRE
			VIOLET/WHITE	TACHOMETER INPUT WIRE
	H3/5	______

			BLACK/WHITE	(-) NEUTRAL SAFETY SWITCH INPUT
			BLACK/WHITE	(-) NEUTRAL SAFETY SWITCH INPUT

16

Image 16

Contents ProSecurity Page Table of contents Page Before beginning the installation Installation points to rememberAfter the installation Locations for the siren Locations for the control moduleLocations for stinger doubleguard shock sensor Locations for valet/program switch Locations for the status LEDFinding the wires you need Locations for the optional starter kill relayLocations for the relay satellite Obtaining constantFinding the 12V switched ignition wire Finding the starter wireFinding the tachometer wire Finding the accessory wireFinding the wait-to-start bulb wire for diesels Finding a + parking light wire Finding the door pin switch circuitMaking your wiring connections Auxiliary harness H2, 6-pin connector Door lock harness, 3-pin connector Heavy gauge relay satellite wiring diagram Primary harness H1 wire connection guide H1/3 WHITE/BLUE remote start activation input H1/5 Green door trigger input, zone H1/8 Black chassis ground connection Secondary harness H2 wire connection guide Page Relay key satellite interface wire connection guide Connect this wire to the ignition wire in the vehicle Remote start secondary harness H3 wire con- nection guide Neutral safety switch interface Figure aTesting the neutral safety switch Sense wire shutting down the unit prematurely Directed Electronics, Inc. Vista, CA Bypassing GM vehicle anti-theft systems Vats Passlock I and passlock II PL-1 and PL-2 Passkey III PK-3, transponder-based systemsPlug-in LED and valet/program switch Shock sensor harness, 4-pin connector Tach learning Programming jumpersTach threshold on/off Light flash +Function Wire Color Transmitter configurations Standard configurationMulti-level security arming PressingSystem features learn routine Tings. The sire will chirp once if connected. Pressing Feature menus Menu #1 basic featuresMenu #2 advanced features Menu #3 remote start optionsFeature descriptions Menu #2 advanced features Page Tion from 1-60 minutes Page Valet mode Nuisance prevention circuitryTimer mode Table of zonesTo perform shutdown diagnostics Shutdown diagnosticsLong term event history Safety check Troubleshooting Alarm troubleshootingRemote start troubleshooting Page Wiring quick reference guide Quick reference guide Get Started Get Protected