Heat & Glo LifeStyle 6000TRS-CE manual Installing the Trim, Installing the Ceramic Re, Fractory

Page 33

CAUTION

1.Apply only non- combustible facing material to the fire- place surround.

IF JOINTS BETWEEN THE FINISHED WALLS AND THE FIREPLACE SURROUND (TOP AND SIDES) ARE SEALED, A 150º C. MINIMUM SEALANT MATE-

RIAL MUST BE USED. THESE JOINTS ARE NOT REQUIRED TO BE SEALED. ONLY NONCOMBUS- TIBLE MATERIAL (USING 150º C. MINIMUM ADHE-

SIVE, IF NEEDED) CAN BE APPLIED AS FACING TO THE FIREPLACE SURROUND. SEE FIGURE 31.

TOP SEAL

FINISH MATERIAL

MAY BE COMBUSTIBLE

JOINT

- TOP AND SIDES OF UNIT

SIDE SEAL

 

JOINT

 

 

1,3 cm

 

1,3 cm

Figure 31. Sealant Material

Step 10 Installing Trim, Refractory, Logs, and Ember Material

Installing the Trim

Combustible materials may be brought up to the specified clearances on the side and top front edges of the fireplace, but MUST NEVER overlap onto the front face. The joints between the finished wall, fireplace top and sides can only be sealed with a 150º C minimum sealant.

Install optional marble and brass trim surround kits as desired. Marble, brass, brick, tile, or other noncombustible materials can be used to cover up the gap between the sheet rock and the fireplace.

Do not obstruct or modify the

! WARNING: CHILDREN AND ADULTS

air inlet/outlet grilles. When

SHOULD BE ALERTED TO THE HAZARDS

OF HIGH TEMPERATURES OF WORKING

overlapping on both sides,

SURFACES ON THESE HEATERS. WORKING

leave enough space so that the

SURFACES INCLUDE ALL GLASS PANELS

bottom grille can be opened

AND DECORATIVE DOORS. YOUNG CHIL-

and the trim door removed.

DREN SHOULD BE CAREFULLY SUPERVISED

 

WHEN THEY ARE IN THE SAME ROOM AS THE

Installing the Ceramic Re-

APPLIANCE.

fractory

 

Remove dress guard, glass

 

door and log package. Remove

 

refractory pieces from packaging

 

(see Figure 32). Position rear

 

refractory piece first and then

 

slide both side pieces through

 

the upper guide openings until

 

they sit firmly against the rear

 

of the unit. See following pages

 

for log installation instruction.

 

Figure 32.

Heat & Glo • 6000TRS-CE • 2049-900 Rev. Q • 2/11

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents What to do if you smell gas ModelSafety and Warning Information Maintaining and Servicing Installing the FireplaceService Parts Log Set Assembly6000TRS-CE Service Parts List6000TRS-CE Valve AssemblyAppliance Certification Installation RegulationsANY Such Action MAY Possibly Cause a Fire Hazard Location Centimeters Locating StepFireplace Clearance RequirementsFraming should be constructed of 2 X 4 lumber or heavier Step Framing FireplaceStep Installing Flue System Flue System ApprovalsIdentifying Flue Components DVP4 DVP6 DVP12 Straight UP Flue with ONE 1 90o Elbow Flue with TWO 2 90 Elbows Flue with TWO 2 90 Elbows Flue with Three 3 90 Elbows + H Installing Flue Components Venting Out the Rear FlueVenting Out the Top Flue On the TOP of the heater Install Support BracketsInstalling Support Brackets Install FirestopsFlue Pipe & Firestop Flue Termination For Horizontal Terminations using the DVP-TRAPBe Positioned SO That the Arrow is Pointing UP DVP Termination Cap Outside of the building Alcove Applications Standing Pilot Ignition System Step Positioning Leveling, Securing FireplaceStep Gas Supply Line Step Gas Pressure Requirements Optional AccessoriesFinishing Installing the Trim Installing the Ceramic ReFractory LOG Placement Heat & Glo 6000TRS-CE 2049-900 Rev. Q 2/11 Placing the Ember Material Glass AssemblyDouble-check for faulty components Review safety warnings and cautionsStep Before Lighting Fireplace Double-check for gas leaksStep Lighting Fireplace After the Installation Maintaining Servicing Your Fireplace Make Sure the Flames Standing Pilot Troubleshooting With the pilot lit, and the ON/OFF switch Placed in this Opening Limited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions
Top Page Image Contents