General Venting Information

Your fireplace is approved to be vented either through the side wall, or vertical through the roof.

-Only Majestic venting components specifically approved and labelled for this fireplace may be used.

-Minimum clearances between vent pipes and combustible materials is one (1") inch (25 mm), except where stated otherwise.

-Venting terminals shall not be recessed into a wall or siding.

-Horizontal venting must be installed on a level plane without an inclining or declining slope.

There must not be any obstruction such as bushes, garden sheds, fences, decks or utility buildings within 24" from the front of the termination hood.

Do not locate termination hood where excessive snow or ice build up may occur. Be sure to check vent termination area after snow falls, and clear to prevent accidental blockage of venting system. When using snow blowers, make sure snow is not directed towards vent termination area.

Location of Vent Termination

It is imperative that the vent termination be located observ- ing the minimum clearances as shown on this page.

*Check with local codes or in absence of local codes, with National Fuel Gas Code, ANSI Z223.1 - latest edition for USA, or CAN 1 B1-149.1 and .1 Installation Code for Canada.

	V		C
L	B		C
	B
			Fixed
			Fixed
			Closed
	F	V	Openable
	F	V

Openable

B V

Fixed

Closed

H	N

		B	M
B	V J X	G	M

V KX V A

V TERMINATION CAP	X AIR SUPPLY INLET	G	GAS METER	RESTRICTED AREA
				(TERMINATION PROHIBITED)

A = clearance above grade, veranda, porch, deck, or balcony [* 12 inches (305mm) minimum]

B = clearance to window or door that may be opened 12" (306mm).

C = clearance to permanently closed window [minimum 12 inches (305mm) recommended to prevent con- densation on window]

D = vertical clearance to ventilated soffit located above the termina/ within a horizontal distance of 24 inches (610mm) from the centre-line of the terminal [18 inches (458mm) minimum]

E = clearance to unventilated soffit [12 inches (305mm) minimum

F = clearance to outside comer see next page G = clearance to inside comer see next page

H = * not to be installed above a meter/regulator assem- bly within 36 inches (914mm) horizontally from the centre-line of the regulator

I = clearance to service regulator vent outlet [*72 inches (1828mm) minimum]

J = clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other fireplace [ *12 inches (305mm) minimum]

K = clearance to a mechanical air supply inlet [* 72 inches (1828mm) minimum]

L = † clearance above paved side-walk or a paved driveway located on public property [*84 inches (2133mm) minimum]

M = clearance under veranda, porch, deck [*12 inches (305mm) minimum ‡]

N = Clearance above a roof shall extend a minimum of 24" (610mm) above the highest point when it passes through the roof surface, and any other obstruciton within a horizontal distance of 18" (450mm).

†a vent shall not terminate directly above a side-walk or paved driveway which is located between two single family dwellings and serves both dwellings *

‡only permitted if veranda, porch, deck, is fully open on a minimum 2 sides beneath the floor *

*check with local codes, or in the absence of local codes, with National Fuel Gas Code, ANSI Z223.1 - latest edition

for USA, or CAN 1B1-149.1 and .2 Installation Code for Canada. Note: Local codes or regulations may require different clearances.

- 8 -

BHDR36 specifications

The Vermont Casting BHDR36 is a versatile and high-performing gas fireplace that seamlessly blends efficiency with style. This fireplace is distinguished by its 36-inch width and offers an impressive heat output, making it an ideal choice for both heating purposes and aesthetic appeal in any home setting.

One of the standout features of the BHDR36 is its innovative burner technology. The fireplace utilizes a dual burner system that ensures a consistently high efficiency rating, generating ample warmth while minimizing gas consumption. This is particularly beneficial for homeowners looking to reduce energy costs while enjoying a cozy ambiance.

The design of the BHDR36 is equally impressive. It features a large, tempered glass viewing area that allows for a panoramic view of the mesmerizing flames. This expansive glass front not only enhances the aesthetic appeal but also improves the overall heating performance by providing greater radiant heat distribution throughout the room. The minimalist design complements various interior styles, making it an excellent addition to both traditional and contemporary spaces.

Furthermore, the BHDR36 is equipped with Vermont Castings’ advanced heating technologies, including a built-in fan that circulates warm air effectively and evenly throughout the space. This ensures that every corner of the room receives warmth, eliminating cold spots and enhancing comfort during the colder months.

Ease of use is another hallmark of the BHDR36. It features a convenient remote control that allows users to adjust the flame height and heat settings with ease. The fireplace’s electronic ignition system ensures a reliable start-up every time, and the adjustable flame allows for a customizable experience based on individual preferences.

Safety is paramount, and Vermont Castings has designed the BHDR36 with this in mind. It includes features such as a safety shut-off valve and a protective screen to prevent accidental contact with the flames. These safety elements provide peace of mind for families and pet owners alike.

In summary, the Vermont Casting BHDR36 is a perfect combination of cutting-edge technology, stylish design, and user-friendly features. With its efficient heating capabilities, extensive viewing area, and significant attention to safety, it stands out as a top choice for homeowners looking to enhance their living spaces with a reliable and beautiful gas fireplace.