DVS 30-2 Standing Pilot Lighting Instructions, What to do if YOU Smell GAS

Page 29

STANDING PILOT LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

A.This fireplace has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions ex- actly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch;

do not use any phone in your building.

Immediately call your gas supplier from a neigh- bor's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it; call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service techni- cian to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

1.STOP! Read the safety information above.

2.Set REMOTE/OFF/ON switch to OFF.

3.Turn off all electric power to the fireplace (if applicable).

4.Lower louver front assembly.

5.Push in gas control knob slightly and turn clockwise to "OFF."

NOTE: Knob cannot be turned from "PILOT" to "OFF" unless knob is pushed in slightly. Do not force.

6.Wait ten (10) minutes to clear out any gas. Then smell for gas, including near the floor. If you then smell gas, STOP! Follow "B" in the safety information above. If you do not smell gas, go to the next step.

7. Find pilot — Follow metal tube from gas control. The pilot is behind the second log on the left side.

8.Turn gas control knob counterclockwise to "PILOT."

9.Push in control knob all the way and hold in. Immediately light the pilot with the Piezo Pilot Ignitor or use a match. Continue to hold the control knob in the for about one (1) minute after the pilot is lit. Release knob, and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 5 through 9.

If the control knob does not pop up when released, STOP and IMMEDIATELY call a qualified service technician or gas supplier.

If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician or gas supplier.

10.Turn gas control knob counterclockwise to the "ON."

11.Close louver front assembly.

12.Turn on all electric power to the appliance (if applicable).

13.Set ON/OFF/REMOTE switch to desired setting.

TO TURN OFF GAS TO FIREPLACE

1.Set REMOTE/OFF/ON switch to OFF.

2.Turn off all electric power to the fireplace if service is to be performed (if applicable).

3.Lower louver front assembly.

4.Push in gas control knob slightly and turn clock-

wise to "OFF." Do not force.

5.Close louver front assembly.

13369-1-0203

Page 29

Image 29
Contents Installation Instructions Table of Contents Important Safety Information LP-GAS Warning Odor Safety Information for Users of LP-GASIntroduction Fireplace Dimensions Model DVS-30/DVS-36/DVS-42 SpecificationsHeater Baffle is Used on DVS-36 & DVS-42 only Fireplace Component InstallationClearances Mantel Chart FigureLocating Fireplace Clearances FigureChecking Manifold Pressures Installing a New Main Gas CockGAS Supply Venting Fireplace InstallationExample a Example BFraming Figure Three 3 basic types of installationsFinishing Figure Vent Runs Figures 14, 15, 16, 17Installation Vertical Sidewall Application Positioning the Fireplace Cutting the Hole Figures 22 MAXInformation on Various Venting Routes and Components Vertical Sidewall InstallationsTermination Clearances Vent Clearances Inner flue joints do not require any sealant Installing Vent Components FigureVent System Identification DVS-30 Framing and Finishing Installing Support Brackets FigureInstalling Firestops Figures 30, 31, 32 DVS-30 Framing and Finishing DVS-36 & DVS-42 Framing and Finishing Installing Firestops Figures 35, 36, 37DVS-36 & DVS-42 Framing and Finishing Vertical Termination For All Models Installing the Vent System in a ChaseReassembly and Resealing Vent Pipe System LOG PlacementVertical Through the Roof Applications Figure Glass RemovalDVS-30 Placement of glowing embers Glass ReplacementDVS-36 and DVS-42 Placement of glowing embers TOP View of LOG SETMillivolt System Figures 48 Standing Pilot Operating InstructionsFlame Appearance Recommended Wire Gauges Standing Pilot Wiring Diagram What to do if YOU Smell GAS Standing Pilot Lighting InstructionsFrequent pilot outage problem Standing Pilot TroubleshootingPilot and main burner extinguish while in operation Glass sootsElectrical Connection Figure DVS-36 & DVS-42 Intermittent Pilot Wiring DiagramTo Turn OFF GAS to Appliance Operation SpecificationsTrial for Ignition CheckoutMain Burner Operation Safety LockoutARC Length Action Ignition System ChecksDVS-36 & DVS-42 Intermittent Pilot Troubleshooting RF Standing Pilot Operating Instructions RF Wiring Diagram RF Standing Pilot Lighting Instructions Please Note Maintenance and ServiceDVS-30 Parts List HOW to Order Repair Parts#41 Orifice NAT DVS-36 Parts ListDVS-42 Parts List Parts View Louvers Accessory PartsVariable Speed Blower Installation Instructions Blower Motor FBB1A Blower Installation Optional Single Speed Blower Installation InstructionsParts List Optional Fresh Air Intake Kit Figure Optional Fresh AIR Intake KIT DVFB-AK-30, FB-AK-2Example of Installation Parts List Installing Optional Brick LinerBrick Liner KIT DVS-BL-30-2, DVS- BL-36-2, DVS-BL-42-2