DVS 30-2 installation instructions Parts List

Page 49

Wiring

The appliance, when installed, must be electrically grounded in accor- dance with local codes or, in the absence of local codes, with the National Electrical Code ANSI/NFPA No. 70, if an external electrical source is utilized. This appliance is equipped with a three-prong [grounding] plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. For an ungrounded receptacle, an adapter, which has two prongs and a wire for grounding, can be purchased, plugged into the ungrounded receptacle and its wire connected to the receptacle mounting screw. With this wire completing the ground, the appliance cord plug can be plugged into the adapter and be electrically grounded.

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

Blower Motor

The blower motor does not have oiling holes. Do not attempt to oil the blower motor.

Blower Wheels

The blower wheels will collect lint and could require periodic cleaning. If the air output decreases or the noise level increases, it indicates a dirty blower wheel. Remove blower and clean blower wheels.

WARNING:

Unplugging of blower accessory will not stop the heater from cycling. To turn off gas to the unvented heater: Push in gas control knob slightly and turn clockwise to “OFF.” Do not force.

Figure 3

PARTS LIST

INDEX

PART

DESCRIPTION

QUANTITY

NUMBER

NUMBER

 

SUPPLIED

1

11935

BLOWER DIVERTOR

1

2

R-6458

CORD SET

1

3

10758

FAN CONTROL BRACKET

1

4

R-2503

FAN CONTROL

1

5

R-6459

WIRE HARNESS

1

6

11932

BLOWER SUPPORT

1

7

R-6460

BLOWER ASSEMBLY

1

8

11933

SWITCH BRACKET

1

9

R-6461

SWITCH

1

NS

10146

BLOWER GASKET

2

NS

R-1720

CABLE CLIP

1

NS

R-1499

GROMMETS

3

NS

R-1454

BUSHING

3

 

 

 

 

13369-1-0203

Page 49

Image 49
Contents Installation Instructions Table of Contents Important Safety Information LP-GAS Warning Odor Safety Information for Users of LP-GASIntroduction Fireplace Dimensions Model DVS-30/DVS-36/DVS-42 SpecificationsHeater Baffle is Used on DVS-36 & DVS-42 only Fireplace Component InstallationClearances Mantel Chart FigureLocating Fireplace Clearances FigureGAS Supply Installing a New Main Gas CockChecking Manifold Pressures Venting Fireplace InstallationExample a Example BFraming Figure Three 3 basic types of installationsFinishing Figure Vent Runs Figures 14, 15, 16, 17Installation Vertical Sidewall Application Positioning the Fireplace Cutting the Hole Figures 22 MAXTermination Clearances Vertical Sidewall InstallationsInformation on Various Venting Routes and Components Vent Clearances Vent System Identification Installing Vent Components FigureInner flue joints do not require any sealant Installing Firestops Figures 30, 31, 32 Installing Support Brackets FigureDVS-30 Framing and Finishing DVS-30 Framing and Finishing DVS-36 & DVS-42 Framing and Finishing Installing Firestops Figures 35, 36, 37DVS-36 & DVS-42 Framing and Finishing Vertical Termination For All Models Installing the Vent System in a ChaseReassembly and Resealing Vent Pipe System LOG PlacementVertical Through the Roof Applications Figure Glass RemovalDVS-30 Placement of glowing embers Glass ReplacementDVS-36 and DVS-42 Placement of glowing embers TOP View of LOG SETFlame Appearance Standing Pilot Operating InstructionsMillivolt System Figures 48 Recommended Wire Gauges Standing Pilot Wiring Diagram What to do if YOU Smell GAS Standing Pilot Lighting InstructionsFrequent pilot outage problem Standing Pilot TroubleshootingPilot and main burner extinguish while in operation Glass sootsElectrical Connection Figure DVS-36 & DVS-42 Intermittent Pilot Wiring DiagramTo Turn OFF GAS to Appliance Operation SpecificationsTrial for Ignition CheckoutMain Burner Operation Safety LockoutARC Length Action Ignition System ChecksDVS-36 & DVS-42 Intermittent Pilot Troubleshooting RF Standing Pilot Operating Instructions RF Wiring Diagram RF Standing Pilot Lighting Instructions Please Note Maintenance and ServiceDVS-30 Parts List HOW to Order Repair Parts#41 Orifice NAT DVS-36 Parts ListDVS-42 Parts List Parts View Louvers Accessory PartsVariable Speed Blower Installation Instructions Blower Motor FBB1A Blower Installation Optional Single Speed Blower Installation InstructionsParts List Optional Fresh Air Intake Kit Figure Optional Fresh AIR Intake KIT DVFB-AK-30, FB-AK-2Example of Installation Parts List Installing Optional Brick LinerBrick Liner KIT DVS-BL-30-2, DVS- BL-36-2, DVS-BL-42-2