Enviro 50-1472, C-11253, C-11102 owner manual KIT Components, Installation Instructions

Page 23

Initial Installation

QUALIFIED INSTALLERS ONLY

DIRECT VENT VERTICAL VENT TERMINATION:

For use with Sonnet Direct Vent Fireplace Insert. The Vertical Vent Cap is termination, rain cap, and a throat connector, it will ensure a tight seal, top performance, safety and efficiency.

KIT COMPONENTS:

Quantity

Description

Quantity

Description

 

 

 

 

1

Vertical Direct Vent Termination Cap

1

4 oz Tube RTV Silicone

 

 

 

 

6

9/16” Tex Screws

1

4 oz Tube Mill-Pac Sealant

Please ensure that all components are supplied with this kit. If components are missing or have been damaged, contact your dealer, distributor, or courier company. Do not attempt the installation if components are missing or damaged.

INSTALLATION INSTRUCTIONS:

1.Plan your installation and clearances to combustibles. The Sonnet may be installed and vented into any solid fuel fireplace that has been installed in accordance with the National, Provincial/State and local building codes and has been constructed of non-combustible materials. Also refer to the INITIAL

INSTALLATION - PREPARING YOUR SONNET FOR INSTALLATION and CLEARANCES TO COMBUSTIBLES sections.

Refer to Figure 43 throughout installation.

2.Stretch both the Ø3” (76mm) flex vent and the Ø2” (51mm) flex intake liner to the length needed to ensure the flex can be easily connected to the vent terminal.

3.Install the flex pipe assembly up through the chimney, ensure that the pipe slides through far enough to connect onto the Vertical Vent Cap.

Note: For any chimney over 15’ (4.6m), install the Sonnet 15’ 2” & 3” Flex Vent (part #50-1512) and the Sonnet 2” & 3” Flex Couplers (part #50-1513). Place a bead of sealant on the coupler (Mill- Pac Black sealant for the Ø3” (76mm) and high temperature silicone for the Ø2” (51mm)) Slide the meeting ends of the flex over the coupler and fasten each joint in place with three (3) sheet metal screws through the flex and into the coupler.

4.The Vertical Vent Cap can be installed onto chimneys with flue openings up to 16” (406mm) x 16” (406mm) and the actual flashing is 18”x18” (refer to Figure 41). If the chimney is smaller the cap

should be trimmed down and folded over.

5. Apply a bead of Mill-Pac Black sealant to

Trim flashing

 

the top section of the Ø3” (76mm) vent

 

collar plate. Slide the Ø3” (76mm) flex

as required.

 

 

 

vent over the flue collar and secure with

 

 

three (3) sheet metal screws evenly

 

 

spaced.

 

 

Note: If the fireplace opening is lower

 

 

than 19” (483mm), remove the vent

18"

18"

collar plate from the top of the insert

(457mm)

(457mm)

and connect it securely to the liner as

 

 

stated in Step 4. Check for tears in the

 

 

liner at this point.

Figure 41: Vertical Vent Cap Dimensions.

 

23

Image 23
Contents Consumer InstallerFor Your Safety General Safety PrecautionsTable of Contents Vented GAS Fireplace Heater Sonnet BV/DV NG/LPG Codes And ApprovalsDimensions SpecificationsTrimmable Lighting and Turning OFF Instructions Operating InstructionsAdjustment of Flame Height Setting the TimeSetting C/24 hour or F/12 hour Clock Automatic Pilot ModeSetting the Timer Changing the Mode of OperationMAN Mode Manual Flame Height Adjustment Setting the TemperatureComponent Sound & Reason Remote Control InstructionPilot Flame Maintenance And ServiceReceiver Remote HandsetMethod 1 From Outside the Cabinet Methods for Resetting the ReceiverTo be Installed by a Qualified Service Agency only Conversion Kit Installation Kit Parts ListIs pointing out then the valve is Mantle width and height Initial InstallationQualified Installers only Vent Kit Installation Kit Contents Quantity DescriptionInstall of Intake Air Plug Venting Fireplace Inserts Description Installation of Sonnet DV and BVKIT Components Installation InstructionsVertical Vent Cap Underside Electrical Requirements Removing/Installing Back Panel Fan Kit InstallationGas Line Connection Fan Only ReplacementLabeled Gas Valve To Test Valve PressuresProper Pilot Flame Installation OptionsInstallation Secondary InstallationScrew Hook Bracket To the Trim AssemblyMinimum size of Large Removal InstallationEnsure the Sonnet is turned off and allow the unit to cool Hook PlacementsEmpty firebox showing the ledges for the back logs Third Stage Log Set Installation Never operate the fireplace with the glass door removed Log Set and Ember InstallationProblem Possible Cause Solution Trouble ShootingValve’s Possible Cause SolutionBV only Reference Part Description Part Number Parts ListNumber Parts ListOption Description Parts Diagram Components Parts Diagram Options To the Dealer WarrantyWarranty Warranty Installation Data Sheet