Waterford Appliances T25-LP DURA-VENT Termination KIT, Planning Your Dura-Vent Installation

Page 15

INSTALLATION

of 1-3/8"(35mm). Use Mill-Pac to seal and secure with 3 of the #8 x 1/2" screws (stainless steel).

4)Attach the adjustable pipe section to the vent terminal using Mill-Pac and/or high temperature silicone and attach with 3 of the #8 x 1/2" screws (stainless steel).

Hint: Apply the sealant (Mill- Pac and/or high temperature sil- icone) to the out- er pipe before connecting the inner pipe.

Note: The pipe seam should be facing down.

Note: To make the i n s t a l l a t i o n more aesthet- ically pleasing, w e r e c o m - mend framing out a square that the cap can b e m o u n t e d on.

Note: If installing termination on a siding covered wall, a vinyl siding stand- off or furring strips must be used to ensure that the termination is not recessed into the siding. For vinyl siding standoff installation refer to the Dura-Vent Termina- tion instructions.

5)Slide the partially connected pipe and vent terminal assembly through the wall thimbles (from the exterior into the interior) and secure the cap to the exterior wall with 4 of the supplied screws (#8 x 1-1/2" drill point, stainless steel). Note: pilot holes will need to be drilled through the wall thimble on all 4 corners.

Note: The four screws provided for the vent cap should be replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

6)A bead of non-hardening mastic should be run around both the termination and vinyl siding standoff to prevent water from en- tering and to make a tight seal between the cap and the standoff.

7)Stretch the 4" dia. flex liner out fully and get a trial fit of the liner onto the 4" dia. starter collar.

8)Cut the 4" dia. flex liner to the desired size.

Hint: leave an extra 12" to 16" of length, this will make the final assembly easier to work with.

9)Secure the 4" dia. flex liner to the 4" adapter with Mill-Pac and 3 of the #8 x 1/2" screws (stainless steel).

10)Slide the decorative Thimble Cover over the pipe sections and secure with 4 screws (#8 x 1-1/2" drill point, black) to the wall.

11)Slide the 90o elbow (crimp end up), the 45o elbow and the 2 ft. or 4 ft. pipe section (crimp end up) over the 4" dia. flex liner.

12)Slide the trim collar over the adjustable pipe sections to cover the joint of the telescopic section.

13)Install the spring spacers onto the pipe sections.

14)Secure the 4" dia. flex liner with adapter onto the stove collar. Put a bead of Mill-Pac around the appliance adapter and secure with 3 screws (#8 x 1/2, stainless steel).

15)Attach the 45o elbow onto the starter collar by sealing with Mill-Pac and/or high tem- perature silicone and securing with 3 of the #8 x 1/2" (black) screws.

16)Attach the pipe section to the 45o elbow by sealing with Mill-Pac and/or high tempera- ture silicone and securing with 3 of the #8 x 1/2" screws (black). Pipe seams should be facing the wall.

17)Attach the 90o elbow onto the pipe section by sealing with Mill-Pac and/or high tem- perature silicone and securing with 3 of the #8 x 1/2" screws (black).

18)Slide the adjustable pipe section onto the 90o elbow. The flex may have to be com- pressed back in order for the adjustable pipe to properly mate to the elbow. Seal with Mill-Pac and/or high temperature sil- icone and secure with 3 of the #8 x 1/2" screws (black). Pipe seams facing down.

18)Install the trim collar over the starter collar and secure with a #8 x 1/2" screw (black).

If the pipe needs to be touched up, use only Stove Brite High Temperature Metallic Black Stove Paint.

NOTE: All inner joints must be sealed with Mill-Pac. All outer joints may be sealed with high temperature silicone.

DURA-VENT

TERMINATION KIT

Planning Your Dura-Vent Installation

There are two basic types of Dura-Vent Direct Vent System installations: horizontal termina- tion and vertical termination. Confirm the max- imum horizontal run and maximum vertical rise from the diagram on page 18.

When planning your installation, it will be nec- essary to select the proper length of vent pipe for your particular requirements. For horizontal installations, determine the minimum clearance

Waterford TARA T25 Direct Vent Freestanding Gas Stove

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Tara Direct Vent Freestanding Gas Stove To the New Owner WaterfordTable of Contents Copy of Safety Label for Tara T25 Gas Stove Safety LabelInformation for Mobile Manufactured Homes After First Sale InstallationSpecifications Save These InstructionsClearances to Combustibles General Safety InformationInstallation Checklist Manufactured Mobile Home Additional RequirementsOptional FAN Installation Locating Your GAS StoveTara Clearances Installation Combustion and Ventilation AIR Exterior Vent Terminal Quired. Other parts may be required Planning Your venting InstallationFor your particular installation Minimum components for a Horizontal InstallationHorizontal Installations Below Grade Snorkel InstallationSnorkel Terminations Vertical Termination with CO-LINEAR Flex System DescriptionAlternate Approved Caps Qty. Description DV Stove Horizontal Vent KITDURA-VENT Termination KIT Planning Your Dura-Vent InstallationAlternate Horizontal Termination Caps Rigid Pipe Venting Components4DT-AJB Rigid Pipe Venting Components ListRigid Pipe Venting Horizontal Terminations Rigid Pipe Venting Vertical TerminationsFor both Residential & Manufactured Homes/Mobile Homes Vent Restrictor DURA-VENT Horizontal InstallationsTermination Round Support RDS Square Support SQS Offset ChartCathedral Ceilings Support Extensions Round Rdse or Square SqseConverting a Factory Built Metal Chimney Converting a Masonry ChimneySystem Data Tara T25 High ElevationValve Description GAS Pipe Pressure TestingGAS Connection Conversion KIT From Natural GAS To PropaneReplace yellow Natural Gas label with red Propane label Securing Cast Iron Front Panel Aeration AdjustmentRemoving Cast Iron Front Panel Optional Front GrillLOG Installation Optional Side ShelfOptional Wall Thermostat Final Check Optional Remote ControlWiring Diagram Tara Thermostat Wire TableOperating Instructions Sounds LOG Replacement MaintenanceMaintenance Instructions General Vent MaintenanceInstalling Valve Assembly Glass ReplacementFAN Maintenance Valve MaintenanceReplacement / Spare Parts List Parts ListPage Conditions WarrantyRegister your Waterford online at

T25-LP, T25-NG specifications

Waterford Appliances presents the T25-LP and T25-NG, two exceptional models in the realm of gas fireplaces that combine elegance, efficiency, and advanced technology. These fireplaces are designed to create a warm and inviting ambiance in any living space, making them perfect for both modern and traditional homes.

The T25-LP (liquid propane) and T25-NG (natural gas) models feature a sleek design that seamlessly integrates into various interior settings. One of their standout characteristics is the expansive viewing area, which allows for an unobstructed view of the mesmerizing flames. The clean lines and contemporary aesthetics of the T25 series make them a striking focal point in any room.

Functional elegance is enhanced by the innovative Multi-Stage Burner System, which produces a realistic flame pattern and optimal heat output. This technology ensures that both models deliver a beautiful, natural fire while also prioritizing efficiency. With adjustable flame heights, users can customize their experience to suit their mood, whether they desire a soft glow for a cozy evening or a higher flame for more substantial heating.

Energy efficiency is another key feature of the T25 series. Both models have been designed with high-efficiency ratings, allowing homeowners to enjoy warmth without excessive energy consumption. This not only contributes to lower utility bills but also aligns with environmentally conscious living. The incorporation of electronic ignition ensures a hassle-free start-up process, with the option for a remote control that enhances convenience.

Additionally, the T25 fireplaces are equipped with advanced safety features, including a built-in pressure regulator and safety shut-off valves, providing peace of mind for users. The fireplaces also come with a range of customizable options such as decorative media, including glass and logs, allowing homeowners to tailor the look of their fireplace to their personal style.

The T25-LP and T25-NG models stand out not only for their beauty but also for their performance and reliability. With user-friendly controls and durable construction, these fireplaces provide lasting enjoyment and comfort. Waterford Appliances has engineered these units to be low-maintenance while ensuring high-end performance, making them a superior choice for anyone looking to enhance their living environment with warmth and style. Overall, with cutting-edge technology, elegant design, and user-centered functionality, the T25 series is a remarkable addition to any home.
Top Page Image Contents