Waterford Appliances T25-LP, T25-NG Maintenance Instructions, General Vent Maintenance

MAINTENANCE

MAINTENANCE

INSTRUCTIONS

1)	Always turn off the valve before cleaning.
	For relighting, refer to lighting instructions.
	Keep the burner and control compartment
	clean by brushing and vacuuming at least
	once a year. When cleaning the logs, use
	a soft clean paint brush as the logs are
	fragile and easily damaged.
2)	Clean glass (never when unit is hot), appli-
	ance, and door with a damp cloth. Never

WARNING: CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SUR- FACE TEMPERATURE AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.

Incorrect flame pattern will have small, probably yellow flames, not coming into proper contact with the rear of the burner or thermopile.

use an abrasive cleaner.

The porcelain enamel finished stoves may

be cleaned with ordinary household glass

cleaner and a soft cloth or paper towel.

Never clean when unit is hot and never use

an abrasive cleaner.

3) The heater is finished in a porcelain finish

or with a heat resistant paint and should

only be refinished with heat resistant paint

(not with wall paint). Waterford uses Stove-

Bright Paint - Metallic Black #6309.

Never use an abrasive cleaner on the

porcelain finish as it may scratch the sur-

face.

4) Make a periodic check of burner for proper

position and condition. Visually check the

flame of the burner periodically, making

sure the flames are steady; not lifting or

floating. If there is a problem, call a qualified

service person.

5) Caution: Label all wires prior to disconnec-

tion when servicing controls. Wiring errors

can cause improper and dangerous oper-

ation.

6) The appliance and venting system must be

inspected before use, and at least annual-

ly, by a qualified field service person, to

ensure that the flow of combustion and

ventilation air is not obstructed.

During the annual service call, the burners

should be removed from the burner tray

and cleaned. Replace the embers but do

DO NOT USE THIS APPLIANCE IF ANY PART HAS BEEN UNDER WATER. IMMEDIATELY CALL A QUALIFIED SERVICE TECHNICIAN TO INSPECT THE APPLIANCE AND TO REPLACE ANY PART OF CON- TROL SYSTEM AND ANY GAS CONTROL WHICH HAS BEEN UN- DER WATER.

CLOTHING OR OTHER FLAMMA- BLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLI- ANCE.

8)Each time the appliance is lit, it may cause condensation and fog the glass. This con- densation and fog is normal and will disap- pear in a few minutes as the glass heats up.

Never operate the appliance without the glass properly secured in place or with the door open.

9)Periodically check the pilot flames. Correct flame pattern has three strong blue flames: 1 flowing around the thermopile and 1 around the thermocouple, and 1 flowing across the rear of the burner (it does not have to be touching the burner).

Note: If you have an incorrect flame pat- tern, contact your Waterford deal- er for further instructions.

Top View of pilot flame

GENERAL VENT

MAINTENANCE

Conduct an inspection of the venting system semi-annually. Recommended areas to inspect as follows:

1)Check the Venting System for corrosion in areas that are exposed to the elements. These will appear as rust spots or streaks, and in extreme cases, holes. These compo- nents should be replaced immediately.

2)Remove the Cap, and shine a flashlight down the Vent. Remove any bird nests, or other foreign material.

3)Check for evidences of excessive conden- sation, such as water droplets forming in the inner liner, and subsequently dripping out the joints, Continuous condensation can cause corrosion of caps, pipe, and fittings. It may be caused by having excessive lateral runs, too many elbows, and exterior portions of the system being exposed to cold weather.

4)Inspect joints, to verify that no pipe sections or fittings have been disturbed, and conse- quently loosened. Also check mechanical supports such as Wall Straps, or plumbers' tape for rigidity.

not block the pilot.

7) Keep the area near the appliance clear and

free from combustible materials, gasoline,

and other flammable vapours and liquids.

CAUTION: ANY SAFETY SCREEN OR GUARD REMOVED FOR SERV- ICING AN APPLIANCE MUST BE REPLACED PRIOR TO OPERAT- ING THE APPLIANCE.

Top View of pilot flame

LOG REPLACEMENT

The unit should never be used with broken logs. Turn off the gas valve and allow the unit to cool before opening door to carefully remove the logs. The pilot light generates enough heat to burn someone. If for any reason a log should need replacement, you must use the proper replacement log. The position of these logs must be as shown in the diagram under Log Installa- tion.

Note: Improper positioning of logs may create carbon build-up and will al- ter the unit’s performance which is not covered under warranty.

Waterford TARA T25 Direct Vent Freestanding Gas Stove 31