Waterford Appliances T25-NG, T25-LP Glass Replacement, FAN Maintenance, Valve Maintenance

MAINTENANCE

GLASS

REPLACEMENT

Your TARA stove is supplied with high temper- ature, 5 mm Neoceram ceramic glass that will withstand the highest heat that your unit will produce. In the event that you break your glass by impact, purchase your replacement door from an authorized Waterford dealer only, and follow our step-by-step instructions for re- placement.

Replacement Part # W260040 Tara Glass

WARNING: Do not operate appliance with glass panels removed, cracked or bro- ken. Replacement of the glass should be done by a licensed or qualified service person.

Note: Wearing gloves will protect your hands while handling glass.

1)Remove the cast iron front panel, grasp it at the bottom and lift the panel upwards and out from the stove. Once free of the locating tabs, the panel can be dropped down; freeing it from the top of the stove.

Place the cast iron front panel on a non- abrasive surface, away from any traffic to ensure that it does not get damaged.

2)Remove the Front Glass Panel. Using a 7/16" socket wrench, remove the 6 hex head bolts used to secure the glass panel and frame to the stove. Remove the frame and glass panel.

3)Using a flat screwdriver, pry open the 4 retaining tabs holding the glass panel in place and remove the old glass.

5)Insert the glass (with gasket) in to the frame so that the 'bulb' portion of the gasket is exposed.

6)Using a flat screwdriver, close the 4 retain- ing tabs used to hold the glass in place.

7)Replace the Front Glass Panel on the stove and reinstall the Cast Iron Front Panel.

FAN MAINTENANCE

If your fan requires maintenance or replace- ment, access to the fan is through the rear access panel on the back of the unit. NOTE:the unit MUST NOT be operated without the fan access panel securely in place and correctly sealed.

IMPORTANT: These fans collect a lot of dust from within your home. Ensure you maintain these fan mo- tors on a regular basis by vacuum- ing out the fan squirrel cages, around the motor, and around the grills on the back of the stove.

IMPORTANT

Disconnect power supply

before servicing

VALVE MAINTENANCE

If your valve requires maintenance or replace- ment, use the following instructions.

Note: Always close off the gas supply

before removing the valve.

1)If optional fan is installed, disconnect power source to stove.

2)Remove control panel.

3)Disconnect gas line to stove.

4)Disconnect 3/8" NPT pipe from 90o elbow on valve.

5)Disconnect the two (2) switch wires from valve.

6)Disconnect piezo wire.

7)Remove the cast iron front panel for easier access.

8) Remove the 4 screws holding the gas valve assembly to the bracket.

9) Remove the thermopile wire.

10) Remove thermocouple with a 9 mm (met-

ric) wrench.

11) Remove pilot nut with an 11 mm wrench.

12) Remove valve to orifice nut with a 13/16"

wrench.

13) Remove inlet pipe with pipe wrench. Note

orientation of 90o elbow.

4)Take the new glass and fit the 'tadpole' glass gasket around the edge of the glass.

WARNING:

Electrical Grounding Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock haz- ard and should be plugged direct- ly into a properly grounded three- prong receptacle. Do not cut or remove the grounding prong from this plug.

To remove fan: Follow the

installation in- structions on page 7 in re- verse.

14) Remove valve and remove gas out 90o

brass fitting. Note orientation of fitting.

Installing Valve Assembly

1)To install a new valve assembly, reverse instructions for removing valve . See above.

2)Check for leaks and manifold pressure. See Gas Pressure Test instructions.

Screw

Screw

Screw

Screw

Stove Front

Valve Bracket with Valve - Top View

32 Waterford TARA T25 Direct Vent Freestanding Gas Stove