Lopi Yankee Bay Pellet Insert manual Maintenance3, Door Seal, Door Alignment

Page 31

Maintenance3 1

Yearly Maintenance (or every two tons) - Continued

Door Seal

! Air leaks into the firebox will decrease the stove's performance greatly, leading to excessive sooting, inefficient burning, and perhaps a malfunction.

• The door gasket must contact the entire perimeter of the door and create an air- tight seal. To verify this, open the door, hold a dollar bill against the body of the heater, close the door, and secure the latch. The dollar bill should be held firmly in place (check the entire perimeter of the door. If it is loose or falls out, the door must be adjusted (see the following page).

Door Alignment

Because the door is three-sided, it is crucial the door is aligned correctly. We recommend that you open the hopper lid and look down upon the door and body of the heater. Use the illustration to the right to determine the correct door alignment.

Correctly Aligned Door

When properly adjusted, the door should be evenly spaced from the front of the stove (and shut tight, compressing the gasket).

Hinge

Latch

Top of Stove

Door

Note how both corners are evenly spaced.

Latch Too Tight - In the illustration below, the latch is too tight (this is the most common mis- alignment). Loosen the latch and tighten the hinge.

Note how the gasket separates from the body.

Hinge Too Tight - In the illustration below, the hinge is too tight. Loosen the hinge and tighten the latch.

Note how the gasket separates from the body.

Travis Industries

4 0 5 0 5 0 9

1 0 0 - 0 1 1 4 5

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Yankee Bay Pellet Insert Introduction Important Information 2IntroductionTravis Industries 5 0 5 0 0 0 1 1 4 Table of Contents 4Safety Precautions Mobile Home Safety Precautions6Specifications Installation7 Hopper Extension Set-up 8InstallationRe-install the hopper walls following the directions below Installation90Installation Venting the Pellet Stove Installation1Mobile Home Requirements 2InstallationOutside Air used for combustion Too Much Air Baffle InstallationRestrictor Adjustment Not Enough AirSurround Panel & Circuit Board Installation 4InstallationHint Installation into a Masonry FireplaceInstallation into a Factory Built Metal 6InstallationStarting the Heater for the First Time Safety NoticeOperation1 Location of ControlsLoading Pellets 8OperationTwo Modes of Operation To Shut Down Manual ModeTo Adjust the Heat To StartTo Adjust Room Temperature or Start the Stove Auto Mode0Operation Operation2 Adjusting the Fan Speed2Operation Make Sure Pellets are Not Piling Up Maintenance2Daily Maintenance whenever using the heater Inspect the BurnCleaning the Firepot 4MaintenanceCheck Firepot for Clinkers Vacuum Hopper Bi-Weekly Maintenance or every 10 bags of pelletsClean the Heat Exchange Tubes Cleaning the Optional Plated SurfacesOpening The Door 6MaintenanceCheck Baffles, Ashbox, Ashpan, Dispose Ash If Necessary Clean the GlassSweep Ash Into Ashpan 8MaintenanceYearly Maintenance or every two tons Clean the Vent make sure the heater and vent is cool 0MaintenanceDoor Seal Maintenance3Door Alignment Adjusting the Door Hinge and Latch 2MaintenanceCheck for Air Leaks Around the Door, Glass, and Ashpan Replacement Parts4Normal Operating Sounds Serial No Safety LabelYears 1 & 2 Coverage Parts & Labor Limited 7 Year WarrantyThermostat Optional EquipmentRemote Thermostat 8Optional EquipmentOptional Log ZC Kit 9 9 2 0 0 1 4 0Index

Yankee Bay Pellet Insert specifications

The Lopi Yankee Bay Pellet Insert is an exceptional heating solution designed for homeowners seeking both efficiency and elegance. This state-of-the-art pellet insert combines advanced technology with a sleek design, making it a popular choice for enhancing home comfort while reducing energy costs.

One of the standout features of the Lopi Yankee Bay Pellet Insert is its high efficiency rating. With a thermal efficiency of over 85%, this insert maximizes the heat output from each pellet, allowing you to enjoy a warm and inviting living space without excessive energy consumption. The intelligent design ensures that less fuel is used, making it an environmentally friendly option as well.

The insert utilizes a patented Smart Control technology that simplifies the heating process. This system ensures optimal performance by automatically adjusting the combustion cycle based on the desired temperature. Users can easily set their preferred temperature using a remote control or a wall-mounted thermostat, providing unmatched convenience. The automatic ignition system enhances usability, allowing for quick and effortless starts.

Another impressive feature of the Lopi Yankee Bay Pellet Insert is its large hopper capacity. With the ability to hold up to 40 pounds of pellets, the insert requires less frequent refueling, giving users more time to enjoy the warmth without constant maintenance. Additionally, the large viewing window features a beautiful bay design that showcases the mesmerizing flames, adding a cozy ambiance to any room.

Durability and craftsmanship are evident in the build of the Lopi Yankee Bay Pellet Insert. Constructed from heavy-duty steel, it is designed to withstand the rigors of daily use while maintaining its stylish appearance. The unit is available in several finishes, ensuring it complements your home's décor seamlessly.

The safety features integrated into the Lopi Yankee Bay Pellet Insert include a heat shield and a sealed combustion chamber, which prevent heat loss and minimize the risk of fire hazards. These attributes make it a safe choice for families, providing peace of mind alongside comfort and efficiency.

In summary, the Lopi Yankee Bay Pellet Insert stands out as a leading option for homeowners looking to upgrade their heating systems. Its combination of efficiency, advanced technology, and aesthetic appeal makes it a wonderful investment for a warm and inviting home.
Top Page Image Contents