Lopi Yankee Bay Pellet Insert manual Optional Equipment, Thermostat

Page 37

Optional Equipment

3 7

Thermostat (Part # 99300650)

!Do not connect 120 VAC to the thermostat circuit of this heater (do not use a household thermostat used for a wall-board or other electical heater).

1Attach the thermostat wire to the circuit board (see the illustration to the right). Route the wire through the back of the heater (away from any hot or moving components).

Attach the quick-connects to the two posts near the molex connector on the circuit board (orientation does not mater).

2Determine a location for the thermostat that is within range of the 20' length of thermostat wire. It should be centralized in the room and away from the heater. The wire may be routed externally on the wall or behind the wall (preferred).

3Follow the directions to the right to attach the thermostat and thermostat wires.

50 60 70 80 90

50 60 70 80 90

Robertshaw

Pull the cover off the thermostat

Run the thermostat wires through the wall (cut off excess wire, leaving 6” of slack).

Expose 1/2” of wire and attach to these two posts.

Standard

Screwdriver

Attach the thermostat to the wall through these two holes.

Travis Industries

4 0 5 0 5 0 9

1 0 0 - 0 1 1 4 5

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Yankee Bay Pellet Insert Introduction Important Information 2IntroductionTravis Industries 5 0 5 0 0 0 1 1 4 Table of Contents 4Safety Precautions Mobile Home Safety Precautions6Specifications Installation7 Hopper Extension Set-up 8InstallationRe-install the hopper walls following the directions below Installation90Installation Venting the Pellet Stove Installation1Mobile Home Requirements 2InstallationOutside Air used for combustion Restrictor Adjustment Baffle InstallationNot Enough Air Too Much AirSurround Panel & Circuit Board Installation 4InstallationHint Installation into a Masonry FireplaceInstallation into a Factory Built Metal 6InstallationOperation1 Safety NoticeLocation of Controls Starting the Heater for the First TimeLoading Pellets 8OperationTwo Modes of Operation To Adjust the Heat Manual ModeTo Start To Shut DownTo Adjust Room Temperature or Start the Stove Auto Mode0Operation Operation2 Adjusting the Fan Speed2Operation Daily Maintenance whenever using the heater Maintenance2Inspect the Burn Make Sure Pellets are Not Piling UpCleaning the Firepot 4MaintenanceCheck Firepot for Clinkers Clean the Heat Exchange Tubes Bi-Weekly Maintenance or every 10 bags of pelletsCleaning the Optional Plated Surfaces Vacuum HopperOpening The Door 6MaintenanceCheck Baffles, Ashbox, Ashpan, Dispose Ash If Necessary Clean the GlassSweep Ash Into Ashpan 8MaintenanceYearly Maintenance or every two tons Clean the Vent make sure the heater and vent is cool 0MaintenanceDoor Seal Maintenance3Door Alignment Adjusting the Door Hinge and Latch 2MaintenanceCheck for Air Leaks Around the Door, Glass, and Ashpan Replacement Parts4Normal Operating Sounds Serial No Safety LabelYears 1 & 2 Coverage Parts & Labor Limited 7 Year WarrantyThermostat Optional EquipmentRemote Thermostat 8Optional EquipmentOptional Log ZC Kit 9 9 2 0 0 1 4 0Index

Yankee Bay Pellet Insert specifications

The Lopi Yankee Bay Pellet Insert is an exceptional heating solution designed for homeowners seeking both efficiency and elegance. This state-of-the-art pellet insert combines advanced technology with a sleek design, making it a popular choice for enhancing home comfort while reducing energy costs.

One of the standout features of the Lopi Yankee Bay Pellet Insert is its high efficiency rating. With a thermal efficiency of over 85%, this insert maximizes the heat output from each pellet, allowing you to enjoy a warm and inviting living space without excessive energy consumption. The intelligent design ensures that less fuel is used, making it an environmentally friendly option as well.

The insert utilizes a patented Smart Control technology that simplifies the heating process. This system ensures optimal performance by automatically adjusting the combustion cycle based on the desired temperature. Users can easily set their preferred temperature using a remote control or a wall-mounted thermostat, providing unmatched convenience. The automatic ignition system enhances usability, allowing for quick and effortless starts.

Another impressive feature of the Lopi Yankee Bay Pellet Insert is its large hopper capacity. With the ability to hold up to 40 pounds of pellets, the insert requires less frequent refueling, giving users more time to enjoy the warmth without constant maintenance. Additionally, the large viewing window features a beautiful bay design that showcases the mesmerizing flames, adding a cozy ambiance to any room.

Durability and craftsmanship are evident in the build of the Lopi Yankee Bay Pellet Insert. Constructed from heavy-duty steel, it is designed to withstand the rigors of daily use while maintaining its stylish appearance. The unit is available in several finishes, ensuring it complements your home's décor seamlessly.

The safety features integrated into the Lopi Yankee Bay Pellet Insert include a heat shield and a sealed combustion chamber, which prevent heat loss and minimize the risk of fire hazards. These attributes make it a safe choice for families, providing peace of mind alongside comfort and efficiency.

In summary, the Lopi Yankee Bay Pellet Insert stands out as a leading option for homeowners looking to upgrade their heating systems. Its combination of efficiency, advanced technology, and aesthetic appeal makes it a wonderful investment for a warm and inviting home.
Top Page Image Contents