Lopi Yankee Bay Pellet Insert manual 8Installation, Hopper Extension Set-up

Page 8

8Installation

Hopper Extension Set-up

This pellet heater has a variable-height hopper. This allows the hopper to be lowered for smaller fireplaces. Follow the instructions below to set the correct hopper extension position.

•Determine the correct hopper extension position following the directions below.

The unit will extend 14” into the fireplace. For setting the hopper, the maximum fireplace opening measurements have to be taken at 14” into the fireplace.

Hopper Extension Position

A (highest position)	25-3/4”
B (next highest)	24-1/2”
C etc...	23-3/8”
D etc...	22-1/4”
E etc...	21-1/8”
F (lowest position)	20”

•Remove the hopper top following the directions below.

Hopper Top

Remove the hopper top by removing the screws holding it in place.

1/4" Nutdriver

NOTE: with the hopper top removed, the hopper walls may be removed.

•Remove the hopper walls.

Travis Industries

4 0 5 0 5 0 9

1 0 0 - 0 1 1 4 5

Image 8

Contents Yankee Bay Pellet Insert Travis Industries 5 0 5 0 0 0 1 1 4 2IntroductionIntroduction Important Information Table of Contents 4Safety Precautions Safety Precautions Mobile Home6Specifications Installation7 8Installation Hopper Extension Set-upInstallation9 Re-install the hopper walls following the directions below0Installation Installation1 Venting the Pellet StoveOutside Air used for combustion 2InstallationMobile Home Requirements Baffle Installation Restrictor AdjustmentNot Enough Air Too Much Air4Installation Surround Panel & Circuit Board InstallationInstallation into a Masonry Fireplace Hint6Installation Installation into a Factory Built MetalSafety Notice Operation1Location of Controls Starting the Heater for the First TimeTwo Modes of Operation 8OperationLoading Pellets Manual Mode To Adjust the HeatTo Start To Shut Down0Operation Auto ModeTo Adjust Room Temperature or Start the Stove Adjusting the Fan Speed Operation22Operation Maintenance2 Daily Maintenance whenever using the heaterInspect the Burn Make Sure Pellets are Not Piling UpCheck Firepot for Clinkers 4MaintenanceCleaning the Firepot Bi-Weekly Maintenance or every 10 bags of pellets Clean the Heat Exchange TubesCleaning the Optional Plated Surfaces Vacuum Hopper6Maintenance Opening The DoorClean the Glass Check Baffles, Ashbox, Ashpan, Dispose Ash If Necessary8Maintenance Sweep Ash Into AshpanYearly Maintenance or every two tons 0Maintenance Clean the Vent make sure the heater and vent is coolDoor Alignment Maintenance3Door Seal 2Maintenance Adjusting the Door Hinge and LatchReplacement Parts Check for Air Leaks Around the Door, Glass, and Ashpan4Normal Operating Sounds Safety Label Serial NoLimited 7 Year Warranty Years 1 & 2 Coverage Parts & LaborOptional Equipment ThermostatOptional Log 8Optional EquipmentRemote Thermostat ZC Kit 9 9 2 0 0 1 4 0Index

Yankee Bay Pellet Insert specifications

The Lopi Yankee Bay Pellet Insert is an exceptional heating solution designed for homeowners seeking both efficiency and elegance. This state-of-the-art pellet insert combines advanced technology with a sleek design, making it a popular choice for enhancing home comfort while reducing energy costs.

One of the standout features of the Lopi Yankee Bay Pellet Insert is its high efficiency rating. With a thermal efficiency of over 85%, this insert maximizes the heat output from each pellet, allowing you to enjoy a warm and inviting living space without excessive energy consumption. The intelligent design ensures that less fuel is used, making it an environmentally friendly option as well.

The insert utilizes a patented Smart Control technology that simplifies the heating process. This system ensures optimal performance by automatically adjusting the combustion cycle based on the desired temperature. Users can easily set their preferred temperature using a remote control or a wall-mounted thermostat, providing unmatched convenience. The automatic ignition system enhances usability, allowing for quick and effortless starts.

Another impressive feature of the Lopi Yankee Bay Pellet Insert is its large hopper capacity. With the ability to hold up to 40 pounds of pellets, the insert requires less frequent refueling, giving users more time to enjoy the warmth without constant maintenance. Additionally, the large viewing window features a beautiful bay design that showcases the mesmerizing flames, adding a cozy ambiance to any room.

Durability and craftsmanship are evident in the build of the Lopi Yankee Bay Pellet Insert. Constructed from heavy-duty steel, it is designed to withstand the rigors of daily use while maintaining its stylish appearance. The unit is available in several finishes, ensuring it complements your home's décor seamlessly.

The safety features integrated into the Lopi Yankee Bay Pellet Insert include a heat shield and a sealed combustion chamber, which prevent heat loss and minimize the risk of fire hazards. These attributes make it a safe choice for families, providing peace of mind alongside comfort and efficiency.

In summary, the Lopi Yankee Bay Pellet Insert stands out as a leading option for homeowners looking to upgrade their heating systems. Its combination of efficiency, advanced technology, and aesthetic appeal makes it a wonderful investment for a warm and inviting home.