0Operation, Auto Mode | Lopi Yankee Bay Pellet Insert manual

Lopi Yankee Bay Pellet Insert manual 0Operation, Auto Mode

Page 20

2 0Operation

Auto Mode

Auto mode allows you to use a thermostat to control room temperature. The stove automatically turns on when the temperature drops below the thermostat setting. Once the stove reaches operating temperature, the stove then runs at the heat output setting selected.

To Adjust Room Temperature (or Start the Stove)

Move the thermostat to the heat setting desired. If the room is cooler than the setting, the stove will go through the start-up sequence for approximately 10 minutes. During this period the lowest “HEAT OUTPUT” light will flash. Once up to temperature, the stove will then run at the heat output setting selected on the control panel. If the room is too hot, move the thermostat to a lesser setting.

To Adjust the Heat

Press the "Heat” buttons to adjust the heat output.

HINT:

If you find that the stove turns on and off repeatedly, you may wish to turn the heat output to a lesser setting. The lower setting will provide a more consistent heat output over time, eliminating the need for the thermostat to repeatedly turn the stove off.

NOTE:

If the thermostat calls for heat while the stove is still cooling down, the stove will go through the start-up sequence (for a minimum of 20 minutes).

	DISCONNECT POWER BEFORE SERVICE
H
E		REMOTE
A	HIGH
T	HIGH		AUTO
T

O		MANUAL
U		MANUAL
T
P
U		AUGER
T	LOW	AUGER		These lights
	LOW		FAULT	These lights
			FAULT	indicate the
				heat output
			AUTO	setting.
			AUTO
H	UP		OFF	NOTE: the
H	UP	MANUAL		lights may
E				be difficult to
A				see from an
T	DOWN		MANUAL	angle.
	DOWN		MANUAL
F	UP		START
F
A
N				Press the
	DOWN			“up” or
				“down”
				button to
				adjust the
				heat output.
			TM
	TRAVIS INDUSTRIES
	HOUSE OF FIRE

To Shut Down

Move the mode switch to "OFF". The exhaust blower will still run until the heater cools down.

AUTO

H UP OFF

EMANUAL

T DOWN MANUAL

UP START

AMANUAL

DOWN

AUGER

TRAVIS INDUSTRIES

HOUSE OF FIRE

Travis Industries

4 0 5 0 5 0 9

1 0 0 - 0 1 1 4 5

Image 20

Contents

Yankee Bay Pellet Insert Travis Industries 5 0 5 0 0 0 1 1 4 2IntroductionIntroduction Important Information Table of Contents 4Safety Precautions Safety Precautions Mobile Home6Specifications Installation7 8Installation Hopper Extension Set-upInstallation9 Re-install the hopper walls following the directions below0Installation Installation1 Venting the Pellet StoveOutside Air used for combustion 2InstallationMobile Home Requirements Baffle Installation Restrictor AdjustmentNot Enough Air Too Much Air4Installation Surround Panel & Circuit Board InstallationInstallation into a Masonry Fireplace Hint 6Installation Installation into a Factory Built MetalSafety Notice Operation1Location of Controls Starting the Heater for the First TimeTwo Modes of Operation 8OperationLoading Pellets Manual Mode To Adjust the HeatTo Start To Shut Down0Operation Auto ModeTo Adjust Room Temperature or Start the Stove Adjusting the Fan Speed Operation22Operation Maintenance2 Daily Maintenance whenever using the heaterInspect the Burn Make Sure Pellets are Not Piling UpCheck Firepot for Clinkers 4MaintenanceCleaning the Firepot Bi-Weekly Maintenance or every 10 bags of pellets Clean the Heat Exchange TubesCleaning the Optional Plated Surfaces Vacuum Hopper6Maintenance Opening The DoorClean the Glass Check Baffles, Ashbox, Ashpan, Dispose Ash If Necessary8Maintenance Sweep Ash Into AshpanYearly Maintenance or every two tons 0Maintenance Clean the Vent make sure the heater and vent is coolDoor Alignment Maintenance3Door Seal 2Maintenance Adjusting the Door Hinge and LatchReplacement Parts Check for Air Leaks Around the Door, Glass, and Ashpan4Normal Operating Sounds Safety Label Serial NoLimited 7 Year Warranty Years 1 & 2 Coverage Parts & LaborOptional Equipment ThermostatOptional Log 8Optional EquipmentRemote Thermostat ZC Kit 9 9 2 0 0 1 4 0Index

Lopi Yankee Bay Pellet Insert manual 0Operation, Auto Mode