Lopi Yankee Bay Pellet Insert manual 2Installation, Mobile Home Requirements

Page 12

1 2Installation

Mobile Home Requirements

•Outside air is required (used for combustion) - see the directions below.

WARNING: DO NOT INSTALL IN SLEEPING ROOM.

CAUTION: THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND CEILING/ROOF MUST BE MAINTAINED.

Outside Air (used for combustion)

•Outside air is optional (except in mobile homes or when required by local building codes).

•Must not be drawn from an enclosed space (garage, unventilated crawl space).

•Must not be over 15' long.

•Must be made with 1 3/4" diameter or larger metal or aluminum duct with a metal screen attached to the end to keep out rodents (P.V.C. or other combustible materials may not be used). Use the Travis Industries Outside Air Kit (part # 99200136).

•Must not terminate above or within 1' of the chimney termination.

•Must have a rain cap or down-turned elbow to prevent water from entering.

•Must be located so that it will not become plugged by snow or other material.

12” Min.

Vent Termination

 

Outside air may be drawn through the chimney (15’ maximum length).

 

Outside air may be drawn

 

 

 

from the ash cleanout.

 

 

Travis

Industries

4 0 5 0 5 0 9

1 0 0 - 0 1 1 4 5

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Yankee Bay Pellet Insert 2Introduction Introduction Important InformationTravis Industries 5 0 5 0 0 0 1 1 4 Table of Contents 4Safety Precautions Safety Precautions Mobile Home6Specifications Installation7 8Installation Hopper Extension Set-upInstallation9 Re-install the hopper walls following the directions below0Installation Installation1 Venting the Pellet Stove2Installation Mobile Home RequirementsOutside Air used for combustion Baffle Installation Restrictor AdjustmentNot Enough Air Too Much Air4Installation Surround Panel & Circuit Board InstallationInstallation into a Masonry Fireplace Hint6Installation Installation into a Factory Built MetalSafety Notice Operation1Location of Controls Starting the Heater for the First Time8Operation Loading PelletsTwo Modes of Operation Manual Mode To Adjust the HeatTo Start To Shut DownAuto Mode To Adjust Room Temperature or Start the Stove0Operation Adjusting the Fan Speed Operation22Operation Maintenance2 Daily Maintenance whenever using the heaterInspect the Burn Make Sure Pellets are Not Piling Up4Maintenance Cleaning the FirepotCheck Firepot for Clinkers Bi-Weekly Maintenance or every 10 bags of pellets Clean the Heat Exchange TubesCleaning the Optional Plated Surfaces Vacuum Hopper6Maintenance Opening The DoorClean the Glass Check Baffles, Ashbox, Ashpan, Dispose Ash If Necessary8Maintenance Sweep Ash Into AshpanYearly Maintenance or every two tons 0Maintenance Clean the Vent make sure the heater and vent is coolMaintenance3 Door SealDoor Alignment 2Maintenance Adjusting the Door Hinge and LatchReplacement Parts Check for Air Leaks Around the Door, Glass, and Ashpan4Normal Operating Sounds Safety Label Serial NoLimited 7 Year Warranty Years 1 & 2 Coverage Parts & LaborOptional Equipment Thermostat8Optional Equipment Remote ThermostatOptional Log ZC Kit 9 9 2 0 0 1 4 0Index

Yankee Bay Pellet Insert specifications

The Lopi Yankee Bay Pellet Insert is an exceptional heating solution designed for homeowners seeking both efficiency and elegance. This state-of-the-art pellet insert combines advanced technology with a sleek design, making it a popular choice for enhancing home comfort while reducing energy costs.

One of the standout features of the Lopi Yankee Bay Pellet Insert is its high efficiency rating. With a thermal efficiency of over 85%, this insert maximizes the heat output from each pellet, allowing you to enjoy a warm and inviting living space without excessive energy consumption. The intelligent design ensures that less fuel is used, making it an environmentally friendly option as well.

The insert utilizes a patented Smart Control technology that simplifies the heating process. This system ensures optimal performance by automatically adjusting the combustion cycle based on the desired temperature. Users can easily set their preferred temperature using a remote control or a wall-mounted thermostat, providing unmatched convenience. The automatic ignition system enhances usability, allowing for quick and effortless starts.

Another impressive feature of the Lopi Yankee Bay Pellet Insert is its large hopper capacity. With the ability to hold up to 40 pounds of pellets, the insert requires less frequent refueling, giving users more time to enjoy the warmth without constant maintenance. Additionally, the large viewing window features a beautiful bay design that showcases the mesmerizing flames, adding a cozy ambiance to any room.

Durability and craftsmanship are evident in the build of the Lopi Yankee Bay Pellet Insert. Constructed from heavy-duty steel, it is designed to withstand the rigors of daily use while maintaining its stylish appearance. The unit is available in several finishes, ensuring it complements your home's décor seamlessly.

The safety features integrated into the Lopi Yankee Bay Pellet Insert include a heat shield and a sealed combustion chamber, which prevent heat loss and minimize the risk of fire hazards. These attributes make it a safe choice for families, providing peace of mind alongside comfort and efficiency.

In summary, the Lopi Yankee Bay Pellet Insert stands out as a leading option for homeowners looking to upgrade their heating systems. Its combination of efficiency, advanced technology, and aesthetic appeal makes it a wonderful investment for a warm and inviting home.
Top Page Image Contents