Lopi Yankee Bay Pellet Insert manual Operation2, Adjusting the Fan Speed

Page 21

Operation2 1

Restrictor Adjustment

The exhaust restrictor “fine tunes” your appliance, adjusting the amount of air flowing to the flame.

NOTE: the optimal restrictor position will vary over time as soot builds up inside the exhaust system.

Not Enough Air:

If clinkers develop or the flame appears lazy and slow to blow the ash out of the firepot, pull the restrictor outward until the flame becomes active and the firepot holes remain clean. NOTE: If the restrictor is fully out (“5”), yet the firepot does not remain clean, the stove needs to be cleaned and checked for air leaks (see “Maintenance” section of this manual).

Too Much Air:

If the flames are too active (small, flickering flames) or if burning pellets are expelled from the firepot, move the restrictor rod inwards until the flame slows down and no burning pellets are expelled. Another symptom of too much air is the heater “blowing the fire out” – a condition in which the pellets burn faster than they are fed (this is most common on low)

Adjusting the Fan Speed

AUTO

H UP OFF

EMANUAL

A

T DOWN MANUAL

UP START

F

AMANUAL

N

DOWN

Press the

AUGER “up” or “down” button to

TM

adjust the fan speed.

TRAVIS INDUSTRIES

HOUSE OF FIRE

Travis Industries

4 0 5 0 5 0 9

1 0 0 - 0 1 1 4 5

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Yankee Bay Pellet Insert 2Introduction Introduction Important InformationTravis Industries 5 0 5 0 0 0 1 1 4 Table of Contents 4Safety Precautions Mobile Home Safety Precautions6Specifications Installation7 Hopper Extension Set-up 8InstallationRe-install the hopper walls following the directions below Installation90Installation Venting the Pellet Stove Installation12Installation Mobile Home RequirementsOutside Air used for combustion Restrictor Adjustment Baffle InstallationNot Enough Air Too Much AirSurround Panel & Circuit Board Installation 4InstallationHint Installation into a Masonry FireplaceInstallation into a Factory Built Metal 6InstallationOperation1 Safety NoticeLocation of Controls Starting the Heater for the First Time8Operation Loading PelletsTwo Modes of Operation To Adjust the Heat Manual ModeTo Start To Shut DownAuto Mode To Adjust Room Temperature or Start the Stove0Operation Operation2 Adjusting the Fan Speed2Operation Daily Maintenance whenever using the heater Maintenance2Inspect the Burn Make Sure Pellets are Not Piling Up4Maintenance Cleaning the FirepotCheck Firepot for Clinkers Clean the Heat Exchange Tubes Bi-Weekly Maintenance or every 10 bags of pelletsCleaning the Optional Plated Surfaces Vacuum HopperOpening The Door 6MaintenanceCheck Baffles, Ashbox, Ashpan, Dispose Ash If Necessary Clean the GlassSweep Ash Into Ashpan 8MaintenanceYearly Maintenance or every two tons Clean the Vent make sure the heater and vent is cool 0MaintenanceMaintenance3 Door SealDoor Alignment Adjusting the Door Hinge and Latch 2MaintenanceCheck for Air Leaks Around the Door, Glass, and Ashpan Replacement Parts4Normal Operating Sounds Serial No Safety LabelYears 1 & 2 Coverage Parts & Labor Limited 7 Year WarrantyThermostat Optional Equipment8Optional Equipment Remote ThermostatOptional Log ZC Kit 9 9 2 0 0 1 4 0Index

Yankee Bay Pellet Insert specifications

The Lopi Yankee Bay Pellet Insert is an exceptional heating solution designed for homeowners seeking both efficiency and elegance. This state-of-the-art pellet insert combines advanced technology with a sleek design, making it a popular choice for enhancing home comfort while reducing energy costs.

One of the standout features of the Lopi Yankee Bay Pellet Insert is its high efficiency rating. With a thermal efficiency of over 85%, this insert maximizes the heat output from each pellet, allowing you to enjoy a warm and inviting living space without excessive energy consumption. The intelligent design ensures that less fuel is used, making it an environmentally friendly option as well.

The insert utilizes a patented Smart Control technology that simplifies the heating process. This system ensures optimal performance by automatically adjusting the combustion cycle based on the desired temperature. Users can easily set their preferred temperature using a remote control or a wall-mounted thermostat, providing unmatched convenience. The automatic ignition system enhances usability, allowing for quick and effortless starts.

Another impressive feature of the Lopi Yankee Bay Pellet Insert is its large hopper capacity. With the ability to hold up to 40 pounds of pellets, the insert requires less frequent refueling, giving users more time to enjoy the warmth without constant maintenance. Additionally, the large viewing window features a beautiful bay design that showcases the mesmerizing flames, adding a cozy ambiance to any room.

Durability and craftsmanship are evident in the build of the Lopi Yankee Bay Pellet Insert. Constructed from heavy-duty steel, it is designed to withstand the rigors of daily use while maintaining its stylish appearance. The unit is available in several finishes, ensuring it complements your home's décor seamlessly.

The safety features integrated into the Lopi Yankee Bay Pellet Insert include a heat shield and a sealed combustion chamber, which prevent heat loss and minimize the risk of fire hazards. These attributes make it a safe choice for families, providing peace of mind alongside comfort and efficiency.

In summary, the Lopi Yankee Bay Pellet Insert stands out as a leading option for homeowners looking to upgrade their heating systems. Its combination of efficiency, advanced technology, and aesthetic appeal makes it a wonderful investment for a warm and inviting home.
Top Page Image Contents