Lopi Yankee Bay Pellet Insert manual Installation1, Venting the Pellet Stove

Page 11

Installation1 1

Venting the Pellet Stove

•PELLET VENT MUST MAINTAIN A MINIMUM 3" CLEARANCE TO ANY COMBUSTIBLE (INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER).

•DO NOT CONNECT THE PELLET VENT TO A VENT SERVING ANY OTHER APPLIANCE OR STOVE.

•DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.

Maximum Venting Distance:

•Maximum venting height is 33' (maximum horizontal offset is 10')

•Use no more than 180° of elbows (two 90° elbows, or two 45° & one 90° elbow, etc.).

Pellet Vent Type

•Must be Type "L" vent and/or Type "L" chimney liner.

•Use 4" diameter vent.

Installing the Pellet Vent

•Pellet vent connections must be sealed airtight with 500° F. RTV silicone and screwed together with at least three sheet metal screws.

.RTV °F 500Silicone

Seal each vent section (including adapters, elbows, etc...) by injecting a liberal amount of 500° F. RTV silicone into the gap between sections.

The exhaust quick- connect can be removed to allow for installation and cleaning.

Pellet Vent Termination

•Termination must be a minimum 6" above the top of the chimney (NOTE: the chimney must meet local codes for height above the roof or other obstructions).

•Must have an approved cap (to prevent water from entering).

•Must not be located where it will become plugged by snow or other material.

Travis Industries

4 0 5 0 5 0 9

1 0 0 - 0 1 1 4 5

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Yankee Bay Pellet Insert Travis Industries 5 0 5 0 0 0 1 1 4 2IntroductionIntroduction Important Information Table of Contents 4Safety Precautions Mobile Home Safety Precautions6Specifications Installation7 Hopper Extension Set-up 8InstallationRe-install the hopper walls following the directions below Installation90Installation Venting the Pellet Stove Installation1Outside Air used for combustion 2InstallationMobile Home Requirements Too Much Air Baffle InstallationRestrictor Adjustment Not Enough AirSurround Panel & Circuit Board Installation 4InstallationHint Installation into a Masonry FireplaceInstallation into a Factory Built Metal 6InstallationStarting the Heater for the First Time Safety NoticeOperation1 Location of ControlsTwo Modes of Operation 8OperationLoading Pellets To Shut Down Manual ModeTo Adjust the Heat To Start0Operation Auto ModeTo Adjust Room Temperature or Start the Stove Operation2 Adjusting the Fan Speed2Operation Make Sure Pellets are Not Piling Up Maintenance2Daily Maintenance whenever using the heater Inspect the BurnCheck Firepot for Clinkers 4MaintenanceCleaning the Firepot Vacuum Hopper Bi-Weekly Maintenance or every 10 bags of pelletsClean the Heat Exchange Tubes Cleaning the Optional Plated SurfacesOpening The Door 6MaintenanceCheck Baffles, Ashbox, Ashpan, Dispose Ash If Necessary Clean the GlassSweep Ash Into Ashpan 8MaintenanceYearly Maintenance or every two tons Clean the Vent make sure the heater and vent is cool 0MaintenanceDoor Alignment Maintenance3Door Seal Adjusting the Door Hinge and Latch 2MaintenanceCheck for Air Leaks Around the Door, Glass, and Ashpan Replacement Parts4Normal Operating Sounds Serial No Safety LabelYears 1 & 2 Coverage Parts & Labor Limited 7 Year WarrantyThermostat Optional EquipmentOptional Log 8Optional EquipmentRemote Thermostat ZC Kit 9 9 2 0 0 1 4 0Index

Yankee Bay Pellet Insert specifications

The Lopi Yankee Bay Pellet Insert is an exceptional heating solution designed for homeowners seeking both efficiency and elegance. This state-of-the-art pellet insert combines advanced technology with a sleek design, making it a popular choice for enhancing home comfort while reducing energy costs.

One of the standout features of the Lopi Yankee Bay Pellet Insert is its high efficiency rating. With a thermal efficiency of over 85%, this insert maximizes the heat output from each pellet, allowing you to enjoy a warm and inviting living space without excessive energy consumption. The intelligent design ensures that less fuel is used, making it an environmentally friendly option as well.

The insert utilizes a patented Smart Control technology that simplifies the heating process. This system ensures optimal performance by automatically adjusting the combustion cycle based on the desired temperature. Users can easily set their preferred temperature using a remote control or a wall-mounted thermostat, providing unmatched convenience. The automatic ignition system enhances usability, allowing for quick and effortless starts.

Another impressive feature of the Lopi Yankee Bay Pellet Insert is its large hopper capacity. With the ability to hold up to 40 pounds of pellets, the insert requires less frequent refueling, giving users more time to enjoy the warmth without constant maintenance. Additionally, the large viewing window features a beautiful bay design that showcases the mesmerizing flames, adding a cozy ambiance to any room.

Durability and craftsmanship are evident in the build of the Lopi Yankee Bay Pellet Insert. Constructed from heavy-duty steel, it is designed to withstand the rigors of daily use while maintaining its stylish appearance. The unit is available in several finishes, ensuring it complements your home's décor seamlessly.

The safety features integrated into the Lopi Yankee Bay Pellet Insert include a heat shield and a sealed combustion chamber, which prevent heat loss and minimize the risk of fire hazards. These attributes make it a safe choice for families, providing peace of mind alongside comfort and efficiency.

In summary, the Lopi Yankee Bay Pellet Insert stands out as a leading option for homeowners looking to upgrade their heating systems. Its combination of efficiency, advanced technology, and aesthetic appeal makes it a wonderful investment for a warm and inviting home.
Top Page Image Contents